Error code reference

Miele Dishwasher Error Codes

60 error codes documented with diagnostic procedures.

Have your model number? Get codes specific to your unit.

DrainDrain fault End/Start-Stop/Top Solo flashing simultaneouslyTechnical fault detected at the end of a program, indicating a possible internal…F..ADrain fault; the wash cycle finishes too early indicating filters are clogged, the drain…F..EWater intake fault F0No fault detected in the electronic controls.F00No faults registered in the fault memory.F01Water/heating NTC temperature sensor R30 or its connection leads are short-circuited…F02Water/heating NTC temperature sensor R30 or its connection leads are open-circuited…F03Water in the wash cabinet does not heat up; the programme takes too long (heater-related…F04Heating failure F05Water drainage failure, heater level switch.F06Too few pulses at flow meter during start of water intake.F07Too few pulses at flow meter during end of water intake.F08Water intake failure, heater level switch.F09Heater level switch not switching on at the end of thermal stops.F0EWater inlet fault; the water supply may be closed, the water inlet filter may be clogged…F1NTC sensor leads or temperature controls open-circuited.F10Heating level switch has switched back at the end of step ZT1, ZT2, ZT3, or ZT4.F11Drainage fault; water is present in the appliance and is not being drained off F12Water intake fault at start of step; during the first 5 seconds of any water intake step…F13Water intake fault at end of step; the desired number of flow meter pulses has not been…F14Water intake fault at heater pressure switch; with the circulation pump operating after a…F15Water intake fault F18Flow meter stationary state monitor B3-4; unexpected pulses from the flow meter are…F19Flow meter B3/4 stiff and not turning freely F2NTC sensor leads or temperature controls short-circuited.F24Heater relay contact fault; 18 seconds after starting the drain sequence, 120VAC is…F25Target temperature fault F26Boiling protection F2EWater inlet fault related to insufficient water pressure (below 14.5 psi) or water supply…F3Electronics fault-program selector switch position was not recognized.F32Door lock does not close F33Door lock does not open F36Door lock switch defective; door switch S4 and door movement switch S80 are closed at the…F4Temperature has exceeded 194°F (90°C) as determined by the Temperature Sensor; the…F40Electronic fault; the electronic has a hardware fault that cannot be repaired by the…F42Line frequency registration fault F47Faulty interface between the Selection-Display Electronic (BAE) and the Control-Power…F5Water drain fault-unit will not drain.F51Heater pressure switch fault F52Heater pressure switch has reset during heating; program continues without heater…F53Speed sensor fault F6Heating level switch fault (Niveauschalter Heizung).F63Slide shutter fault; even though slide shutter motor has been activated, there is no…F67Circulation pump speed too low; check is carried out 10 seconds after the circulation…F68Circulation pump operating after shutoff; the frequency converter registers a speed…F69Circulation pump blocked; with the circulation pump operating, heater pressure switch…F7Water inlet fault-too few pulses at the beginning of the step.F70Float switch fault F78Circulation pump fault; interrupted connection between the electronic and the door…F79Circulation pump communication fault; faulty communication between the circulation pump…F8Water inlet fault-too few pulses at the end of the step.F84Slide shutter positioning fault; an attempt to position the slide shutter has been…F85Slide shutter signal change fault F86Salt container lid contact fault F87Sensor softener fault F88Turbidity sensor fault; false or no values from turbidity sensor F9Water inlet fault-heating level switch did not activate (circulation pump not pumping…F91Load size registration inactive; water intake block operates with default water quantity…IntakeWater intake fault

Get the full diagnostic procedure for any code

Step-by-step tests, expected values, wiring diagram references, and verified part numbers.

Get Started $9.95 3-day pass

$29/month for unlimited access to all brands and Max AI diagnostics.

More Miele error codes

Common questions

How do I find the error code on my Miele Dishwasher?

Most Miele dishwashers show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.

Are these codes specific to my model?

The codes here apply broadly to Miele dishwashers. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.

What do I do if my code is not listed?

Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.

How much does it cost to access the full diagnostic procedures?

A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.