Skip to main content
Error code reference
Miele Oven Error Codes
52 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
ECEnergy-Conservation feature is active; the oven has shut off the heat and is using…F 09Catalyst Temperature SensorF 23Pre-Heat Self Clean Fault (460°F was not reached in the allotted time).F 32Door Lock not locking during Self Clean mode (fault is stored after 20 seconds if the…F 33Door lock not unlocking after self-clean mode (fault is stored after 20 seconds if the…F 43Programming FaultF 55The oven did not automatically turn off after a specified time of operation (dependent on…F05Oven Pt1000 temperature sensor (1R30-10) or its connections short-circuited.F06Oven Pt1000 temperature sensor (1R30-10) or its connections open-circuited, or plug at…F07Software fault displayed in service mode or via MDU; not applicable to DGC models.F1The water container is not installed in the appliance.F10Steam generator water intake faultF102Communication module defective.F103Communication module incompatible.F11Steam generator drainage faultF13The pyrolitic door-locking device does not close (drive, door cable, or door temperature…F134Temperature read by oven temperature sensor is too high; cavity temperature sensor or…F14The pyrolitic door-locking device does not open (drive, door cable, or door temperature…F15The correct pyrolitic temperature has not been reached after 120 minutes (excessive…F16Identity lost; programmed model variant has been deleted.F17The catalyser temperature sensor Pt 1000 is open-circuited or its resistance is too great.F190Plumbed-water connection valve defectiveF191Heat-flow Pt1000 temperature sensor (2R30-10) or wiring harness short-circuited.F192Heat-flow Pt1000 temperature sensor (2R30-10) or wiring harness open-circuited.F193Bottom heat Pt1000 temperature sensor (R30/22) or wiring harness short-circuited.F194Bottom heat Pt1000 temperature sensor (R30/22) or wiring harness open-circuited.F195Roast probe electronic communication faultF196Pump sump faultF197Cooling-air Pt1000 temperature sensor (R30-34) short circuit.F198Cooling-air Pt1000 temperature sensor (R30-34) open circuit.F20Heating faultF235Control/power electronic communication faultF241Touchpad communication faultF242Touchscreen communication faultF260Temperature difference in cavity temperature sensor.F263Impermissibly high temperature registered.F265PEC fault (internal fault).F3Roast probe short-circuited.F38Electronics software versions incompatible.F4The NTC temperature sensor contains a short circuit or open circuit.F44Control electronic (2N1) / power electronic (1N1) communication interface is defective.F47Communication fault between power/display and control electronics.F5Oven PTC temperature sensor short-circuited.F54Roast probe short-circuited in its connection to ET 7440 or ELP 7440 electronic.F57Cooling fan defective.F6The oven has automatically turned itself off during operation as a safety feature…F60Power electronic (N1-1) temperature limit exceeded due to insufficient cooling and…F7The cooling fan has stopped turning or is turning too slowly.F74Drain valve not functioning at steam generator.F8The convection fan has stopped turning.F9The maximum temperature of the oven has been exceeded and the oven has turned itself off…F94Plumbed-water connection water intake fault
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More Miele error codes
Common questions
How do I find the error code on my Miele Oven?
Most Miele ovens show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to Miele ovens. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.