mypros+
Error code reference

Miele Dishwasher Error Code F47

Faulty interface between the Selection-Display Electronic (BAE) and the Control-Power Electronic (SLT)…

Miele codesMiele dishwasher codes

Faulty interface between the Selection-Display Electronic (BAE) and the Control-Power Electronic (SLT); communication between BAE and SLT is faulty.

First step from the service manual

Replace the electronic (Section 008-4.1).

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F47.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F47 means on a Miele dishwasher

Error code F47 on a Miele dishwasher indicates a communication failure between two core electronic modules: the Selection-Display Electronic (BAE) and the Control-Power Electronic (SLT). The BAE is the interface board responsible for user input and display functions, while the SLT is the main control and power board that drives the wash cycle operations and manages component outputs. These two boards communicate continuously during operation, and when that communication link breaks down or produces invalid signals, the dishwasher halts and logs F47.

The fault can originate from either board or from the wiring and connectors that link them. A corrupted or failed communication line between the BAE and SLT means the machine cannot reliably coordinate user commands with operational execution, making it unsafe to continue running. Internal component failure within either board, such as a damaged communication chip or failed solder joint, is a common root cause. Loose, corroded, or damaged connectors on the harness between the two boards can also interrupt the data signal without either board itself being defective.

Because this is an inter-board communication fault, basic resets typically do not resolve it. The prescribed diagnostic approach is direct replacement of the electronic module, as outlined in Section 008-4.1 of the technical documentation. Technicians should inspect the wiring harness and connectors between the BAE and SLT before committing to a board replacement, since a damaged connector can mimic a full board failure at a fraction of the cost.

Source: manufacturer service documentation.

Common causes of F47

  1. 01

    Failed BAE or SLT electronic board

    Part replacement

    An internal failure within either the Selection-Display Electronic or the Control-Power Electronic board can corrupt or completely cut off the communication signal between them. This is the most likely cause and typically requires board replacement.

  2. 02

    Loose or disconnected wiring harness connector

    Wiring / connection

    The connector linking the BAE to the SLT can work loose over time due to vibration. Inspecting and reseating the harness connectors between both boards is a critical first step before replacing any components.

  3. 03

    Corroded or damaged harness pins

    Wiring / connection

    Moisture inside the dishwasher cabinet can cause pin corrosion at the BAE-to-SLT connector, degrading the communication signal. Visually inspect the connector pins for oxidation, discoloration, or physical damage.

  4. 04

    Damaged wiring between the two boards

    Part replacement

    Chafed, pinched, or broken wires in the harness run between the BAE and SLT can intermittently or permanently interrupt communication. A continuity check on the harness can confirm or rule this out.

  5. 05

    Power supply irregularity affecting board initialization

    Wiring / connection

    An unstable power supply to either board during startup can prevent proper handshaking between the BAE and SLT. This may cause F47 to appear intermittently before becoming a permanent fault.

See the test procedure for each cause

Frequently asked questions about F47

What does F47 mean on a Miele dishwasher?
F47 on a Miele dishwasher means the communication link between the Selection-Display Electronic (BAE) and the Control-Power Electronic (SLT) has failed or is producing faulty signals. These two boards must exchange data continuously to run wash cycles properly. When that communication breaks down, the dishwasher stops operating and displays F47. The fault can lie in either board, the connecting harness, or the connectors between them.
Can I fix F47 myself, or does it require a technician?
Diagnosing and resolving F47 requires comfort with disassembling the dishwasher door panel and inspecting or replacing electronic boards. A knowledgeable DIYer can check connectors and wiring for obvious damage, but board-level replacement is the prescribed fix and involves handling sensitive electronic components. If you are not experienced with appliance electronics, a qualified technician is recommended to avoid additional damage.
Will resetting my Miele dishwasher clear the F47 error?
A power reset is unlikely to permanently resolve F47. Because this fault reflects a hardware communication failure between two control boards, the underlying problem will persist after a reset and the code will typically return as soon as the machine attempts to operate. Clearing the fault requires physical inspection and, in most cases, component replacement.
Is it safe to use my dishwasher while F47 is displayed?
No, you should not attempt to run the dishwasher while F47 is active. The machine has detected that its two primary control boards cannot communicate reliably, which means it cannot safely manage the wash cycle, water intake, or heating functions. Continuing to operate it in this state risks improper behavior and potential water damage.
How much does it cost to repair a Miele dishwasher F47 error?
Repair costs for F47 vary depending on whether the fix involves just a connector or harness repair versus full board replacement. Connector or wiring repairs might cost in the range of $75 to $200 for a technician visit and parts. Replacing one or both electronic boards on a Miele dishwasher can range from $200 to $600 or more, depending on the specific boards required and local labor rates.

Related Miele dishwasher codes

All Miele dishwasher codes
View all 59 Miele dishwasher codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass