mypros+
Error code reference

Miele Freezer Error Code 1-1-1

Icemaker

Miele codesMiele freezer codes

Icemaker: Ice production cycle is interrupted.

First step from the service manual

Start icemaker self-test and see if ice tray rotates. If tray does not rotate, check icemaker for mechanical blockage. If blockage exists, replace icemaker.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 1-1-1.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 1-1-1 means on a Miele freezer

Error code 1-1-1 on a Miele freezer indicates that the icemaker's ice production cycle has been interrupted before completing normally. The icemaker relies on a motorized ice tray mechanism that rotates to release formed ice cubes into the collection bin. When this rotation fails to occur or is detected as incomplete, the control board registers the fault and halts further ice production to prevent mechanical damage or overflow conditions.

The primary diagnostic focus for this code is the ice tray's ability to rotate during a self-test cycle. If the tray fails to rotate when the self-test is initiated, the cause is either a mechanical obstruction preventing movement or a failed icemaker drive motor assembly. Ice buildup, a jammed cube, or foreign material lodged in the tray mechanism are common physical blockages that can interrupt the cycle. In these cases, clearing the obstruction may resolve the error without replacing any parts.

If no blockage is found but the tray still does not rotate during the self-test, the icemaker unit itself is likely faulty, involving the internal motor or drive components. In this scenario, the entire icemaker assembly requires replacement, as the internal motor and drive components are not typically serviced separately. Technicians should also confirm the icemaker is receiving proper power and that no wiring harness issues exist before condemning the unit.

Source: manufacturer service documentation.

Common causes of 1-1-1

  1. 01

    Mechanical blockage in ice tray

    Wiring / connection

    Ice buildup, a misshapen cube, or a foreign object can prevent the tray from rotating through its full cycle. Inspect the tray and surrounding area for any obstruction that can be manually cleared.

  2. 02

    Failed icemaker motor or drive assembly

    Part replacement

    If the self-test confirms the tray does not rotate and no blockage is present, the internal motor or drive components within the icemaker unit have likely failed. The full icemaker assembly will need to be replaced.

  3. 03

    Ice accumulation around the tray mechanism

    Wiring / connection

    Excessive frost or ice bridging around the tray pivot points can seize the mechanism without an obvious visible obstruction. Defrosting the icemaker compartment fully may free the tray.

  4. 04

    Wiring or connector issue to the icemaker

    Wiring / connection

    A loose, corroded, or damaged wiring harness connection can interrupt power to the icemaker motor mid-cycle. Inspect the connector at the icemaker for secure seating and signs of damage.

  5. 05

    Faulty icemaker control or sensor

    Part replacement

    An internal sensor within the icemaker that monitors tray position may be sending incorrect signals, causing the control board to register a cycle interruption even when no physical fault is present. Replacement of the icemaker assembly resolves this.

See the test procedure for each cause

Frequently asked questions about 1-1-1

What does 1-1-1 mean on a Miele freezer?
Error code 1-1-1 means the icemaker's ice production cycle was interrupted and did not complete normally. The most common reason is that the ice tray failed to rotate, either due to a physical blockage or a motor failure. The freezer displays this code to alert you that ice production has stopped and the issue needs attention.
How do I fix error code 1-1-1 on my Miele freezer?
Start by running the icemaker self-test to observe whether the ice tray rotates. If the tray does not rotate, inspect the icemaker for any ice buildup, lodged cubes, or foreign objects blocking the mechanism. If no blockage is found and the tray still will not move, the icemaker assembly needs to be replaced. Clearing a blockage or fully defrosting the icemaker area often resolves the error without any part replacement.
Is it safe to keep using my Miele freezer when error code 1-1-1 is active?
The freezer itself should continue to maintain temperature and keep food frozen while this code is active, as the error is isolated to the icemaker system. However, ice production will be stopped until the fault is resolved. It is best to address the issue promptly to avoid any secondary problems such as water leakage if the cycle remains interrupted.
Will resetting my Miele freezer clear error code 1-1-1?
A reset alone is unlikely to permanently clear this code if the underlying problem has not been corrected. If the ice tray is blocked or the motor is faulty, the error will return as soon as the icemaker attempts another production cycle. Resolve the mechanical or component issue first, and the code should clear once normal operation is restored.
How much does it cost to repair error code 1-1-1 on a Miele freezer?
If the issue is just a blockage that can be cleared manually, there may be no parts cost involved, only a service call fee if a technician is used. If the icemaker assembly needs full replacement, parts and labor costs together typically range from around $200 to $500 or more depending on your location and the specific model. Miele appliances often carry premium part costs, so getting a quote before proceeding is recommended.

Related Miele freezer codes

All Miele freezer codes
View all 70 Miele freezer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass