Error code reference
Samsung Microwave Error Code E-08
Function of MWO starts with spit inserted into cavity inside.
Function of MWO starts with spit inserted into cavity inside.
MyPros+ Max
Get the full diagnostic procedure for E-08.
- ✓Step-by-step tests with expected resistance, voltage, and continuity values
- ✓Wiring diagram references and connector pinouts from the OEM service manual
- ✓Verified part numbers when replacement is required
Get the full procedure→
$29/month · Cancel anytime · Or $9.95 3-day pass
M+
M+ Max·Samsung Microwave
E-08 on my Samsung Microwave
M+
Function of MWO starts with spit inserted into
From Service Manual 934479, p.51:
1.Access service mode to confirm the active fault code and read stored error history.
2.Measure control board supply voltage at the test points. Expected: 12 VDC and 5 VDC; a drop below 4.75 VDC on the logic rail points to a failed onboard regulator.
3.Inspect all connectors on the main control for corrosion, thermal stress, or backed-out pins. Reseat each connector with the power disconnected.
Part DA92-00384N
Main PCB assembly
Related Samsung microwave codes
All Samsung microwave codes →- 0tPCB temperature sensor short-circuit error variant (cooling…
- C-10Cooking Sensor information code
- C-2Temperature sensor short circuit detected.
- C-21Temperature Sensor Open or Short information code
- C-22Over temperature information code
- C-3Over 536°F during operation of MWO mode (within 60 seconds)…
- C-A0Damper motor position detection problem.
- C-d0Key Short information code
View all 72 Samsung microwave codes
- C-d1Key short detected on control panel.
- C-F0PCB communication problem between main PCB and display.
- C-F1Touch problem detected on touch film or harness.
- C1No tray
- E-01Door opens when the door should not be opened.
- E-02Cooking time setting over error for microwave (MWO) mode.
- E-03If WARM, CONVECTION, PREHEAT or BROIL do not reach over 217…
- E-04Cooking time setting over error for convection mode (max 45…
- E-05Cooking time setting over error for combination mode (max…
- E-06Swing heater detection failure
- E-09Oven Temperature Error
- E-0AOven Temperature Error
- E-0bCooling fan motor sensor error
- E-0XOther error codes (device-specific, format
- E-11Temperature sensor open error
- E-12Temperature sensor short error
- E-13Preheat max time error
- E-14Gas sensor dry up / no load error
- E-21Temperature sensor open error
- E-22Temperature Sensor Short Error
- E-23If the PREHEAT does not reach the preset temperature within…
- E-24Overheat during cooking causes temperature to reach 500°F…
- E-25Abnormal temperature sensed during microwave cook mode
- E-26Temperature not rising above fixed AD value within first 3…
- E-27Sensor open error variant (temperature sensor related).
- E-28Sensor short error variant (temperature sensor related).
- E-29Sensor open error (temperature sensor variant).
- E-2ASensor short error (temperature sensor variant).
- E-2bCooling fan motor sensor error
- E-2CCooling fan motor sensor error
- E-31Weight sensor open error (when value of HEX is above FF for…
- E-32Weight sensor short circuit error.
- E-33Weight sensor error
- E-34Weight sensor error
- E-35Weight sensor error
- E-36Door opens during sensor cooking (weight sensor mode).
- E-41Easy/PH Sensor Open Error
- E-42Easy/PH Sensor Short Error
- E-43Easy/PH sensor T1 max time error.
- E-44Easy/PH sensor dry up
- E-45Easy/PH sensor cooling error
- E-46Easy/PH sensor primary open error within 3 minutes.
- E-47Door opened during Easy/PH sensor cooking operation.
- E-51EEPROM open error
- E-53EEPROM Read/Write Error.
- E-54EEPROM zero not to be set error.
- E-61Humidity sensor open error
- E-62Humidity sensor short error
- E-63Humidity sensor T1 max time error.
- E-83Communication error between Main PCB and Sub PCB.
- E-A1Damper positioning error (40 seconds).
- E0Gas sensor open/short (sensor value between 6 and 211).
- E1Exceeds T1 time limit (gas sensor).
- E10Problem with the EEPROM.
- E2Open sensor circuit detected.
- E3On the cooling mode, sensor Vout was not less than 4.7V…
- E4Problem with the weight sensor (output frequency = 0 Hz).
- E5Gas sensor short.
- error1Shorted sensor circuit detected.
- error2Open sensor circuit detected.
- error3On the cooling mode, sensor's Vout was not less than 4.7V…
- error4On the way to sensing, the door was opened.
- SEKey Short Error
- TETouch communication error (10 seconds timeout).
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started →$29/month · Cancel anytime · Or $9.95 3-day pass