mypros+
Error code reference

Speed Queen Washer Error Code DOOR/FINAL SPIN LEDs Flashing

Motor failure error

Speed Queen codesSpeed Queen washer codes

Motor failure error – the control received the motor failure signal from the motor control; all outputs are turned off.

First step from the service manual

Check continuity between motor terminals (Tach circuit terminals 4-5 approx 115 ohms; Windings terminals 1-2, 1-3, 2-3 approx 4-5 ohms). Machine must be unpowered to clear this error.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for DOOR/FINAL SPIN LEDs Flashing.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What DOOR/FINAL SPIN LEDs Flashing means on a Speed Queen washer

The DOOR and FINAL SPIN LED flashing simultaneously on a Speed Queen washer indicates a motor failure error. This occurs when the motor control board detects an internal fault condition and sends a failure signal to the main control. Once triggered, the control shuts off all outputs to protect the system from further damage. This error does not clear automatically; the machine must be completely unpowered to reset the fault state.

The motor circuit on these machines includes a tachometer circuit and three winding pairs that can be tested with a multimeter. The tachometer circuit, measured across terminals 4 and 5, should read approximately 115 ohms. The three winding pairs, measured across terminals 1-2, 1-3, and 2-3, should each read approximately 4 to 5 ohms. Readings that fall significantly outside these values point to a failed motor. If winding resistance values are within spec, the fault may originate in the motor control board itself rather than the motor windings.

Common triggers for this error include open or shorted motor windings, a failed tachometer sensor within the motor, wiring harness damage between the motor and the motor control board, or a defective motor control board. Because all outputs are disabled when this error is active, the washer will not operate until the fault is diagnosed and corrected and power has been cycled to clear the stored error condition.

Source: manufacturer service documentation.

Common causes of DOOR/FINAL SPIN LEDs Flashing

  1. 01

    Failed motor windings

    Part replacement

    Open or shorted motor windings will trigger the motor failure signal. Test resistance across terminals 1-2, 1-3, and 2-3; readings significantly above or below 4 to 5 ohms indicate a failed motor.

  2. 02

    Faulty tachometer circuit

    Part replacement

    The tachometer provides motor speed feedback to the control board. Measure across terminals 4 and 5; a reading that deviates substantially from approximately 115 ohms points to a failed tach sensor within the motor.

  3. 03

    Damaged wiring harness

    Wiring / connection

    Broken, corroded, or pinched wires between the motor and the motor control board can interrupt signals and cause a false motor failure error. Inspect the harness for visible damage and check connector pins for corrosion or looseness.

  4. 04

    Defective motor control board

    Part replacement

    If all motor winding and tachometer resistance values test within specification, the motor control board itself may have failed internally and is sending an erroneous failure signal to the main control.

See the test procedure for each cause

Frequently asked questions about DOOR/FINAL SPIN LEDs Flashing

What does DOOR/FINAL SPIN LEDs Flashing mean on a Speed Queen washer?
When both the DOOR and FINAL SPIN LEDs flash simultaneously, the washer is indicating a motor failure error. The motor control board has detected a fault condition and sent a failure signal to the main control, which then shuts off all machine outputs. The washer will not operate again until the motor circuit is diagnosed, the fault is corrected, and the machine is unpowered to clear the error.
Will unplugging my Speed Queen washer clear the DOOR/FINAL SPIN flashing error?
Unplugging the machine is required to clear the stored error, but it will not fix the underlying problem. If the motor fault condition still exists when power is restored, the error will return immediately. The motor and its associated wiring must be diagnosed and repaired before the reset will hold.
How do I fix the motor failure error on my Speed Queen washer?
Start by unplugging the washer, then use a multimeter to check motor resistance at the specified terminals. The tachometer circuit at terminals 4 and 5 should read approximately 115 ohms, and each winding pair at terminals 1-2, 1-3, and 2-3 should read approximately 4 to 5 ohms. Readings outside these ranges indicate a failed motor, while in-range readings with a persistent fault may point to a bad motor control board or wiring harness issue.
Is it safe to use my Speed Queen washer when the DOOR/FINAL SPIN LEDs are flashing?
No, the washer is not safe to operate in this condition. When the motor failure error is active, the control shuts off all outputs and the machine will not run a cycle. Attempting to force operation without addressing the underlying fault could cause further damage to the motor or control board components.
How much does it cost to repair a Speed Queen washer motor failure error?
Repair costs depend on the failed component. A replacement drive motor typically runs in the range of $150 to $350 for the part alone, while a motor control board can range from $100 to $300 or more. Adding professional labor costs will increase the total. If only a wiring harness or connector repair is needed, costs can be significantly lower.

Related Speed Queen washer codes

All Speed Queen washer codes
View all 71 Speed Queen washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass