mypros+
Error code reference

Sub-Zero Wine Storage Error Code 45 2 00

Lights open circuit; main lights relay open.

Sub-Zero codesSub-Zero wine storage codes

Lights open circuit; main lights relay open.

MyPros+ Max

Get the full diagnostic procedure for 45 2 00.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 45 2 00 means on a Sub-Zero wine storage

Error code 45 2 00 on a Sub-Zero wine storage unit indicates an open circuit condition in the interior lighting system, specifically traced to the main lights relay. An open circuit means the electrical path required to power the lights has been broken, preventing current from completing its loop through the lighting circuit. The main lights relay is the switching component responsible for energizing the light circuit on command from the control board. When the relay itself fails in an open state, or when the wiring between the relay and the light fixtures loses continuity, the control board detects the absence of expected current flow and logs this fault code.

The most common hardware failures associated with this code include a burned or failed main lights relay, a broken or disconnected wire in the lighting circuit, a faulty light socket, or a failed LED or incandescent bulb assembly that has created a complete break in circuit continuity. Because the fault is flagged at the relay level, the control board has determined that the open condition exists on the load side of the relay or within the relay contact itself, rather than being a simple bulb outage in a parallel circuit. Diagnosis should focus on verifying relay output voltage and tracing continuity through the full lighting circuit wiring harness.

Source: manufacturer service documentation.

Common causes of 45 2 00

  1. 01

    Failed main lights relay

    Part replacement

    The main lights relay can fail in an open contact position, meaning it no longer passes current to the light circuit even when commanded to close. This is one of the most direct causes of this specific fault code.

  2. 02

    Broken or disconnected wiring in the lighting circuit

    Wiring / connection

    A wire in the lighting harness that has become disconnected, chafed through, or broken will create an open circuit condition. Inspect wiring connections at the relay, control board, and light fixture terminals for visible damage or loose pins.

  3. 03

    Failed light fixture or bulb assembly

    Part replacement

    A completely failed bulb or LED module can break the circuit continuity if the fixtures are wired in series. Check each fixture for signs of burnout or failure.

  4. 04

    Faulty light socket or socket wiring

    Part replacement

    Corrosion or physical damage to a light socket can interrupt the circuit at the point of connection. Inspect sockets for corrosion, burned contacts, or cracked housings.

  5. 05

    Control board relay driver failure

    Part replacement

    If the control board is not sending the correct signal to activate the relay, the relay will remain open. This is less common but should be considered if the relay and wiring both test normal.

See the test procedure for each cause

Frequently asked questions about 45 2 00

What does 45 2 00 mean on a Sub-Zero wine_storage?
Error code 45 2 00 indicates an open circuit condition in the interior lighting system, specifically at the main lights relay. The control board has detected that the lighting circuit is broken and current is not flowing through it. This fault will cause the interior lights to stop functioning entirely. The open circuit can originate at the relay itself, in the wiring harness, or at a light fixture.
Can I fix error code 45 2 00 myself, or do I need a technician?
Some basic checks, such as inspecting for visibly disconnected wires or a burned-out bulb assembly, are within reach of a knowledgeable DIYer. However, testing relay output voltage and diagnosing the control board typically requires a multimeter and familiarity with appliance electrical systems. If you are not comfortable working around appliance wiring, a qualified appliance technician is the safer choice.
Is error code 45 2 00 a safety concern for my wine storage unit?
This fault is specific to the lighting circuit and does not affect the cooling or temperature regulation of the unit. Your wine will remain at the correct storage temperature while this fault is present. The code does indicate an electrical fault that should be addressed, but it is not an immediate safety emergency in most cases.
How much does it cost to repair error code 45 2 00 on a Sub-Zero wine unit?
Repair costs depend on the root cause. If only a wiring connection needs to be reseated, costs may be limited to a service call fee, typically in the range of $100 to $200. Relay or light fixture replacement parts for Sub-Zero units can add $50 to $250 or more depending on the component. A control board replacement, if needed, is the most expensive scenario and can range from $300 to $700 or higher including labor.
Will resetting the unit clear error code 45 2 00?
A reset may temporarily clear the fault code from the display, but if the underlying open circuit condition still exists, the code will return once the control board re-tests the lighting circuit. The physical cause of the open circuit, whether a failed relay, broken wire, or faulty fixture, must be repaired for the code to clear permanently.

Related Sub-Zero wine storage codes

All Sub-Zero wine storage codes
View all 72 Sub-Zero wine storage codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass