mypros+
Error code reference

Viking Oven Error Code EE01

Oven thermistor failure

Viking codesViking oven codes

Oven thermistor failure - software detects break/short-circuit of oven thermistor; oven stuck at too hot in oven mode or too cold in proof (fermentation) mode.

First step from the service manual

Check if the connector between the oven thermistor and board is disconnected or shorted; if not, measure oven thermistor resistance with connector pulled out of the board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for EE01.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What EE01 means on a Viking oven

The EE01 error code on a Viking oven indicates a thermistor failure detected by the oven's control software. The oven thermistor is a temperature-sensing resistor that continuously reports cavity temperature back to the control board. When the software detects that the thermistor circuit has either opened (broken) or shorted, it throws the EE01 fault. A break in the circuit causes the board to read an impossibly low resistance or no signal at all, while a short causes an artificially high or runaway reading. Either condition prevents accurate temperature regulation.

The practical symptoms depend on which direction the fault falls. In standard oven mode, a faulty thermistor often causes the oven to read as too hot, which can result in the burner or element not energizing correctly or shutting off prematurely. In proof or fermentation mode, the failure typically manifests as the oven reading too cold, preventing it from reaching or maintaining the low target temperature required for dough proofing. Both symptom profiles point to a loss of accurate thermistor feedback rather than a heating element problem.

The first step in diagnosis is inspecting the wiring connector between the thermistor and the control board for disconnection, corrosion, or pinched wires that could create a short. If the connector is intact, the thermistor itself should be tested with a multimeter by pulling the connector from the board and measuring resistance directly across the thermistor leads. A reading that is open, shorted, or far outside the expected range for the cavity temperature confirms thermistor failure.

Source: manufacturer service documentation.

Common causes of EE01

  1. 01

    Disconnected thermistor connector

    Wiring / connection

    The wiring connector between the thermistor and the control board may have worked loose over time due to vibration or heat cycling. Inspect the connector at both the thermistor end and the board end for any separation.

  2. 02

    Failed oven thermistor

    Part replacement

    The thermistor itself may have failed internally, resulting in an open or shorted resistance reading when measured with a multimeter after pulling the connector from the board. A faulty thermistor reads outside the normal resistance range for the current cavity temperature and must be replaced.

  3. 03

    Shorted or damaged thermistor wiring

    Part replacement

    The wiring harness running from the thermistor to the control board can become pinched, chafed, or heat-damaged, causing a short circuit in the signal line. Visually inspect the full length of the harness for burned insulation, bare wire contact, or pinch points.

  4. 04

    Corroded or burned connector terminals

    Wiring / connection

    High oven temperatures over years of use can cause the connector terminals to oxidize or burn, increasing resistance in the circuit enough to trigger a fault. Check the connector pins for discoloration, corrosion, or carbon buildup.

  5. 05

    Control board failure

    Part replacement

    If the thermistor and all wiring test within acceptable resistance values, the control board itself may have a fault in the thermistor input circuit, causing it to incorrectly interpret a valid signal as a break or short. Board replacement is typically a last resort after all other components are ruled out.

See the test procedure for each cause

Frequently asked questions about EE01

What does EE01 mean on a Viking oven?
EE01 on a Viking oven means the control software has detected a break or short circuit in the oven thermistor circuit. The thermistor is the temperature sensor that tells the board how hot the oven cavity is. When this sensor or its wiring fails, the oven cannot regulate temperature accurately, causing it to run too hot in bake mode or too cold in proof mode.
Can I fix EE01 on my Viking oven myself?
A knowledgeable DIYer can start by inspecting the thermistor wiring connector for disconnection or visible damage, which requires no special tools. Testing the thermistor resistance with a multimeter after unplugging the connector from the board is also a straightforward step. However, replacing the thermistor or diagnosing a control board issue typically requires comfort with appliance disassembly and electrical testing, and some may prefer a qualified technician for those steps.
Is it safe to use my Viking oven when EE01 is displayed?
It is not recommended to use the oven while EE01 is active. Because the control board cannot accurately read the cavity temperature, the oven may overheat or fail to reach safe cooking temperatures, leading to either a fire risk or improperly cooked food. The oven should remain off until the thermistor fault is diagnosed and resolved.
How much does it cost to repair a Viking oven EE01 error?
Repair costs depend on what has failed. If only the thermistor needs replacement, parts typically range from $30 to $80, with labor adding $100 to $200 depending on your area. If the control board is at fault, parts alone can range from $200 to $500 or more, making the total repair considerably higher. A diagnostic service call is usually needed to confirm which component is responsible before parts are ordered.
Will resetting my Viking oven clear the EE01 error code?
Resetting the oven by cutting power at the breaker may temporarily clear the EE01 code, but the error will return as soon as the control board re-evaluates the thermistor circuit during startup or operation. A reset does not fix the underlying wiring or component problem. The fault needs to be diagnosed and the faulty component repaired or replaced for the error to stay cleared.

Related Viking oven codes

All Viking oven codes
View all 35 Viking oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass