mypros+
Error code reference

Viking Oven Error Code EE02

AH sensor failure

Viking codesViking oven codes

AH sensor failure — break/short-circuit of the AH sensor; software and associated A/D circuitry measuring values outside normal range for AH sensor.

First step from the service manual

Measure element resistance between the opened and sealed sides of the humidity sensor with the connector disconnected from the board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for EE02.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What EE02 means on a Viking oven

The EE02 error code on a Viking oven indicates a failure in the AH (absolute humidity) sensor circuit. This sensor monitors moisture levels inside the oven cavity, and the control board's analog-to-digital (A/D) conversion circuitry continuously reads its output to regulate cooking conditions. When the board detects that the measured values fall outside the acceptable range for the AH sensor, either too high or too low, it flags EE02 to indicate a break or short-circuit condition in that sensor loop.

The AH sensor has two distinct sides: an opened side exposed to the oven cavity atmosphere and a sealed reference side. Proper sensor function depends on a stable resistance differential between these two sides. If a wire breaks, a connector corrodes, or the sensor element itself degrades, the resistance readings become invalid. The control board's software compares incoming A/D values against defined thresholds, and any reading outside that range triggers this fault code.

The first diagnostic step is to disconnect the AH sensor connector from the control board and measure the element resistance across both the opened and sealed sides of the sensor. This isolates whether the fault is in the sensor itself, the wiring harness, or the board's input circuitry. A broken element will typically show an open circuit (infinite resistance), while a short will show near-zero resistance. If resistance on both sides reads within normal range, the issue may lie in the control board's A/D input circuitry rather than the sensor or its wiring.

Source: manufacturer service documentation.

Common causes of EE02

  1. 01

    Failed AH sensor element

    Part replacement

    The humidity sensor element itself can break internally or degrade over time, causing an open or short circuit. This is identified by measuring resistance across the opened and sealed sides of the sensor after disconnecting it from the board.

  2. 02

    Damaged or corroded wiring harness

    Part replacement

    The wires connecting the AH sensor to the control board can crack, fray, or develop corrosion at connector pins, interrupting the signal. Visually inspect the harness for burnt insulation, pinched wires, or corroded terminals.

  3. 03

    Loose or disconnected connector

    Wiring / connection

    A connector that has vibrated loose or was not fully seated will break continuity in the sensor circuit and produce out-of-range A/D readings. Check that the sensor connector is fully clicked into place on both the sensor and the board.

  4. 04

    Moisture or contamination in the sensor connector

    Wiring / connection

    Grease, steam, or cleaning solution can infiltrate the connector and cause a short between pins or high-resistance contact. Inspect the connector for residue and clean or replace as needed.

  5. 05

    Faulty control board A/D circuitry

    Part replacement

    If the sensor and wiring harness both test within normal resistance ranges, the fault may be in the control board's analog-to-digital input circuitry that processes the sensor signal. Board replacement is required in this case.

See the test procedure for each cause

Frequently asked questions about EE02

What does EE02 mean on a Viking oven?
EE02 indicates a failure in the AH (absolute humidity) sensor circuit. The control board has detected that the sensor's measured values are outside the normal acceptable range, pointing to a break or short-circuit in the sensor or its wiring. The control board's software and A/D circuitry monitor this sensor continuously, and EE02 is triggered when the readings become invalid.
Can I fix the EE02 error on my Viking oven myself?
A knowledgeable DIYer can start by checking the AH sensor connector for loose connections, corrosion, or visible wire damage. If comfortable using a multimeter, you can disconnect the sensor connector from the board and measure resistance across the opened and sealed sides of the sensor to determine if the sensor itself has failed. However, if the wiring and sensor test normal, the control board may need professional diagnosis and replacement.
Is it safe to use my Viking oven when it shows EE02?
It is generally not recommended to continue using the oven while this error is active. The AH sensor influences how the control board manages cooking conditions, and operating with a faulty sensor circuit means the oven is not functioning within its designed parameters. Until the fault is diagnosed and resolved, use of the oven should be limited or avoided.
How much does it cost to repair a Viking oven EE02 error?
Repair costs depend on the root cause. If only the AH sensor needs replacement, parts and labor typically range from $150 to $350. If the control board's A/D circuitry is at fault and the board requires replacement, total costs can range from $400 to $800 or more depending on the specific model and labor rates in your area.
Will resetting the oven clear the EE02 error code?
Power-cycling the oven may temporarily clear the EE02 code, but if the underlying sensor fault is still present, the error will return during the next operating cycle. A reset does not repair a broken sensor element, damaged wiring, or faulty board circuitry. Proper diagnosis and component repair or replacement are required to permanently resolve the fault.

Related Viking oven codes

All Viking oven codes
View all 35 Viking oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass