mypros+
Error code reference

Whirlpool Range Error Code F1E0

User Interface Board EEPROM Communication Error-the UI board is locked up due to an unexpected internal communication error, often corrected by…

Whirlpool codesWhirlpool range codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F1E0 error code actually means

Your Whirlpool range has detected a problem with the main control board's internal memory, which stores important settings and calibration data for the appliance. When this memory loses communication or experiences an unexpected error, the board shuts itself down to prevent the range from behaving unpredictably. This is essentially the range's way of saying its 'brain' hit a snag and needs attention before it can operate safely again.

Diagnostic procedure

The full F1E0 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
See TEST #4 (User Interface Input Voltage and Communication).
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F1E0 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F1E0

Ranked by how often they cause this code
  1. 1Transient voltage spike or power fluctuation
  2. 2Faulty main control board (Indigo)
  3. 3Loose or damaged wiring harness to the main control board
  4. 4Corrupted EEPROM data

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F1E0

How do I fix F1E0 on a Whirlpool range?
Start by cycling power to the range. Turn off the breaker or unplug the unit, wait a full 30 seconds, then restore power. This allows the Indigo main control board to fully reset and re-establish its internal EEPROM communication. If F1E0 comes back after the power cycle, the main control board needs to be replaced.
Is it safe to use my Whirlpool range while F1E0 is showing?
No. When F1E0 is active, the main control board is locked up and the range is not functioning normally. Attempting to operate the range in this state is not reliable and could produce unexpected behavior from the controls. Cycle power first, and do not use the range until the error has cleared or the faulty control board has been replaced.
Why does F1E0 keep coming back on my Whirlpool range after I reset it?
If F1E0 returns after a power cycle, the Indigo main control board has likely suffered a hardware failure, either in the EEPROM memory chip itself or in the surrounding communication circuitry. Before replacing the board, check that all wiring harness connectors to the control board are fully seated and free of damage. If connections look good, the control board itself is the part to replace.
What does the F1E0 error code mean on a Whirlpool range?
F1E0 means the Indigo main control board experienced an unexpected EEPROM communication event and locked up. EEPROM is the onboard memory the control board uses to store operating data and settings. When communication to that memory is disrupted, the board halts and displays F1E0 to signal the problem.
How much does it cost to fix a Whirlpool range F1E0 error?
If a power cycle clears the error permanently, there is no cost. If the main control board needs replacement, the part typically runs between $150 and $350 depending on the specific Whirlpool model and supplier. Adding professional labor, expect a total repair cost of $250 to $500. DIY replacement is feasible for someone comfortable with appliance repair since it generally involves disconnecting wire harnesses and swapping the board.

Related Whirlpool range error codes

All Whirlpool range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass