Model reference

Whirlpool GS773LXSS0

Range

6 documents23 error codes6 service modes

Available documentation

Tech Sheet

TECH SHEET - 9762984 - Rev A6 pg
Covers this model
TECH SHEET - Whirlpool Gas Range GS563LXSS06 pg
Covers this model

Service Manual

Whirlpool Gas Range Direct Spark Ignition System29 pg
Covers this model

Installation Guide

Instruction Sheet1 pg
Covers this model
Installation Instructions16 pg
Covers this model
Instruction Sheet2 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool GS773LXSS0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Range

E0 on my Whirlpool GS773LXSS0

M+

No failure. Displays only if user

From Tech Sheet W16049770, p.22:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (23)

CodeMeaning

E0No failure F1 E0EEPROM communications failure, likely caused by power line noise or lightning.F1 E1EEPROM checksum failure, likely caused by power line noise or lightning.F1 E3Fuel type (gas/electric) select failure F1-E0EEPROM communications failure, possibly caused by power line noise or lightning.F1-E1EEPROM checksum failure, possibly caused by power line noise or lightning.F2 E0Key contact closed for more than 60 seconds F2 E1No communication between keyboard and control F2 E6STOP/CLEAR key contact closed for more than 60 seconds F2-E0Key contact closed for more than 60 seconds due to key held down too long…F2-E1No communication between keyboard and control due to keytail loose, unplugged…F3 E0Break in oven sensor circuit F3 E1Short in oven sensor circuit F3 E2BAKE/BROIL temperature out of range (too high)F3 E3Clean temperature out of range (too high)F3-E0Break in oven sensor circuit due to open sensor, loosened or disconnected…F3-E1Short in oven sensor circuit due to shorted sensor, sensor shorted to casing…F3-E2BAKE/BROIL temperature out of range (too high)F3-E3Clean temperature out of range (too high)F5 E0Door switch open during clean F5 E1Door latch not operating F5-E0Door switch open during clean F5-E1Door latch not operating

Service modes (6)

Manual Diagnostics Mode 1Enter within 120 seconds of power-up
Manual Diagnostics Mode 1 (Full - within 120 seconds of power-up)Within 120 seconds of power-up, press Cancel/OFF, Cancel/OFF, then START
Manual Diagnostics Mode 2Enter after 120 seconds of power-up
Manual Diagnostics Mode 2 (Limited - after 120 seconds of power-up)After 120 seconds of power-up, press Cancel/OFF, Cancel/OFF, then START
Temperature AdjustmentPress and hold BAKE pad for five (5) seconds
Temperature Adjustment (Calibration)Press and hold BAKE pad for 5 seconds. Current offset is shown in 3-digit display. CAL is shown in…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass