mypros+
Error code reference

Whirlpool Range Error Code F2-E0

Key contact closed for more than 60 seconds due to key held down too long, shorted key, warped keypad, moisture inside keypad, or missing keytail.

Whirlpool codesWhirlpool range codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F2-E0 error code actually means

Your range has detected a problem with the control panel buttons, specifically that one of the buttons appears to be stuck or is sending a constant signal as if someone is pressing it continuously. This could be caused by a physical button that is stuck in the pressed position, moisture trapped under the keypad, or an internal electrical fault in the keypad itself. The range has stopped normal operation and is displaying this code to let you know the button panel needs to be inspected or replaced.

Diagnostic procedure

The full F2-E0 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Verify failure via manual diagnostics screen 5, then unplug range and inspect keytail connector for damage.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F2-E0 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F2-E0

Ranked by how often they cause this code
  1. 1Shorted keypad membrane
  2. 2Stuck or physically jammed key
  3. 3Loose or damaged keypad ribbon connector
  4. 4Failed control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F2-E0

What does F2-E0 mean on a Whirlpool range?
F2-E0 means the control board has detected a keypad subsystem failure, specifically a shorted keypad or a key that is stuck in the pressed position. The board cannot properly read input from the keypad and displays this code to indicate the fault. Check for debris under the keys first, then inspect the keypad ribbon connection before replacing the keypad.
Can I still use my Whirlpool range with F2-E0 active?
Using the range with F2-E0 active is not recommended. The error indicates the keypad is not functioning reliably, which means you may be unable to control cooking functions, set timers, or cancel a cooking cycle safely. In some cases the oven may not respond to commands at all. Repair the keypad issue before continuing to use the appliance.
Will unplugging my Whirlpool range fix the F2-E0 code?
Unplugging the range for a minute can clear a temporary glitch and is always worth trying first. However, if F2-E0 reappears after restoring power, the keypad has a persistent short or stuck key condition that a reset cannot fix. A power cycle is a diagnostic step, not a repair, and the underlying keypad fault must be addressed.
How do I fix F2-E0 on a Whirlpool range?
Start by disconnecting power to the range for at least one minute to reset the control board. If F2-E0 returns, check that the keypad ribbon connector is fully seated at the control board. If the connection is secure and the code persists, replace the keypad assembly, as Whirlpool's first recommended repair step for this code is keypad replacement. If a new keypad does not clear the error, the control board may need to be replaced.
How much does it cost to fix a Whirlpool range F2-E0 error?
A replacement Whirlpool keypad assembly typically costs between $50 and $150 depending on the model, and replacing it is a moderate DIY repair requiring a screwdriver and basic disassembly of the control panel. If a technician performs the repair, expect an additional $100 to $200 in labor. If the control board is also at fault, a replacement board can cost $150 to $350 or more in parts alone.

Related Whirlpool range error codes

All Whirlpool range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass