Model reference

Amana 109-5W

Air Conditioner

63 error codes12 service modes
MyPros+ Max

Diagnose your Amana 109-5W.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (63)

View all 63 error codes
F2E1Stuck or shorted key on keypad.F3 E0Oven sensor opened.F3 E1Oven sensor shorted.F3 E2Bake range overtemp.F3 E3Clean range overtemp.F3E0Refrigerator/Main compartment (Z1) thermistor short or open circuit.F3E1Freezer/Main compartment (Z1) thermistor short or open circuit.F3E2Refrigerator Evaporator thermistor short or open circuit.F3E3Freezer Evaporator thermistor short or open circuit.F3E4Deli compartment (Z2) thermistor short or open circuit.F3E5Crisper (Z3) thermistor short or open circuit.F4 E1Microwave oven convection thermistor fault.F4 E2Microwave oven internal temperature sensor fault.F4 E4Microwave oven humidity sensor fault.F4E1Microwave convection thermistor sensor failure.F4E2Microwave internal (ambient) temperature sensor failure (integrated on MW…F4E4Microwave humidity sensor failure.F5No feature identified for microwaveF5 E0Door and latch switches do not agree.F5 E1Solenoid not operating or latch switch failure / Latch during clean error.F5E0Door and latch switch do not agree.F5E1Door latch not operating.F6 E5No cavity size commandF6E0Lost communications between user interface and appliance manager.F6E1Cook oven over temperature.F6E2Clean oven over temperature.F6E3Mini oven/warm drawer over temperature (oven not equipped with this feature).F6E4User interface and appliance manager mismatch.F6E5No cavity size command programmed in control.FDE0Ice maker tray thermistor short or open circuit.FDEAIce Maker Jammed (cannot find Homing or end of harvest location).OPOpen circuit detected on thermistor.SHShort circuit detected on thermistor.

Service modes (12)

  • Cavity size programming["Disconnect oven or interrupt power","Wait 10 seconds, reconnect power","Enter diagnostic mode
  • cavity_size_programming1
  • Clear last fault code["Disconnect oven or interrupt power","Wait 10 seconds, reconnect power","Enter diagnostic mode
  • clear_last_error_code1
  • diagnostic["Press the OFF key.","Press the OFF key.","Press the START key.","If control does not enter…
  • Diagnostic component activation["Enter diagnostic mode (OFF, OFF, START)","Press Bake to activate bake relay","Press Broil once…
  • Diagnostic mode["Press OFF","Press OFF","Press START","If the appliance does not enter diagnostic mode, repeat the…
  • diagnostic_troubleshooting_keystrokesWhile in Diagnostic mode (entered via OFF, OFF, START)
  • Fahrenheit/Celsius selection["Press OPTIONS then 1"]
  • Service Diagnostics Mode["Press the pulsing JennAir logo to wake up the UI.","Press the middle zone key.","Press CONNECT…
  • Showroom Mode["Press and hold top and bottom zone icons simultaneously for 3 seconds."]
  • Temperature calibration adjustment["Press OPTIONS then 6","For double oven only, select desired oven (upper or lower)","Press 3 to…

Full entry steps, exit procedures, and test sequences are available in Max.

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass