mypros+
Error code reference

Whirlpool Range Error Code F1-E3

Electronics subsystem failure

Whirlpool codesWhirlpool range codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F1-E3 error code actually means

Your Whirlpool range has detected a conflict between two sources of configuration information on its control board: a small physical switch (called a jumper) and the board's internal memory are giving it different instructions about what type of range it is. Because these settings disagree, the range refuses to operate to avoid running incorrectly. This typically requires a technician to inspect the control board's jumper settings and memory configuration to resolve the mismatch.

Diagnostic procedure

The full F1-E3 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Notify the installer that the jumpers were not reconnected properly.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F1-E3 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F1-E3

Ranked by how often they cause this code
  1. 1Configuration jumper not reconnected after installation or service
  2. 2Configuration jumper installed in wrong position
  3. 3Damaged or missing configuration jumper
  4. 4Corrupted or failed control board EEPROM

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F1-E3

What does F1-E3 mean on a Whirlpool range?
F1-E3 means the control board detected a mismatch between the physical configuration jumper and the settings stored in its EEPROM memory. The jumper tells the board what type of range it is, including cavity size and whether the unit is gas or electric. This code most often appears after installation or a service call where internal wiring was disturbed.
Can I still use my Whirlpool range with the F1-E3 error code active?
Operating the range with an active F1-E3 code is not advisable. Because the control board cannot confirm the correct appliance configuration, cooking functions, temperature calibration, and safety logic may not operate as intended. Resolve the jumper issue before using the range for cooking.
Why did F1-E3 appear on my Whirlpool range right after installation?
This is the most common scenario for F1-E3. The configuration jumper, which identifies the range's cavity size and fuel type to the control board, was likely not reconnected during the installation process. Contact the installer directly and ask them to verify the jumper is seated correctly on the electronics subsystem. This is a recognized installation step they are responsible for completing.
How do I fix F1-E3 on a Whirlpool range?
Start by contacting your installer or the technician who last serviced the range and ask them to verify the configuration jumper was reconnected in the correct position. No tools or parts are required for this check. If the jumper is confirmed correct and the code remains after cycling power, a control board replacement is likely needed.
How much does it cost to fix F1-E3 on a Whirlpool range?
If the fix is simply reseating or repositioning the configuration jumper, the repair may cost nothing beyond a service call fee if a technician performs it, typically ranging from $75 to $150 depending on your area. If the control board requires replacement due to a corrupted EEPROM, parts and labor can run $200 to $400. Always ask whether the jumper was verified before agreeing to a board replacement.

Related Whirlpool range error codes

All Whirlpool range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass