Model reference
Whirlpool 665
Dishwasher
6 documents54 error codes25 service modes
Available documentation
Tech Sheet
- Kenmore Whirlpool Dishwasher Tech Sheet2 pg
- Tech Sheet W10142826A 665 13133K701 KM WP DW2 pg
- Kenmore Whirlpool Dishwasher 665 13973k015 Tech Sheet W103218742 pg
Wiring Diagram
- Kenmore Whirlpool Dishwasher 665 13153K701 Tech Sheet W10082766A2 pg
- Stainless Steel Tub Platform Wiring Diagram / Plastic Tub Platform Wiring Diagram2 pg
Installation Guide
- Instruction Sheet for Heater Element kit2 pg
MyPros+ Max
Diagnose your Whirlpool 665.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (54)
CodeMeaning
1-1Pilot relay K2 stuck on1-2Control software issue10-1Dispenser electrical problem10-2Vent wax motor electrical problem10-3Drying fan error2-1Stuck key detected2-2No response from User Interface3-1Thermistor/OWI open3-2Thermistor/OWI shorted3-3OWI failure or failed calibration4-1Wash motor problem4-2Motor communication error4-4Diverter5-1Door stuck open5-2Door stuck closed5-5Door switch(es)6-1Low/no water (mechanical problem)6-2Fill valve electrical problem6-3Suds/air in pump6-4Float switch open6-6Cool water6-8Flowmeter or regen valve electrical problem7-1No heat7-2Heater stuck on8-1Slow drain8-2Drain motor electrical problem8-3Drain stuck on9-1Diverter can't find position9-2Diverter can't find position (additional instance or variant).9-3Diverter problem (variant).View all 54 error codes
E0EEPROM communications failure.E1EEPROM checksum failure.F0-E0No failureF1EEPROM communications error, EEPROM checksum failure, UL AD error(s).F1-E0EEPROM communications failureF1-E1EEPROM CHECKSUM failureF1-E3Fuel type (gas/electric) select failureF10Clean range over temp.F2Key stuck or held for too long (generated when any key is pressed and held for…F2-E0Key contact closed for more than 60 secondsF2-E1No communication between keyboard and controlF2-E6STOP/CLEAR key contact closed for more than 60 secondsF3Shorted key or key tail unplugged.F3-E0Break in oven sensor circuitF3-E1Short in oven sensor circuitF3-E2BAKE/BROIL temperature out of range (too high)F3-E3Clean temperature out of range (too high)F4Oven sensor opened, oven sensor shorted, bake range over temp, or clean range…F5Door and switches do not agree, door latch not operating, or latch error during…F5-E0Door switch open during CLEANF5-E1Latch switch not operatingF7Oven sensor opened.F8Oven sensor shorted.F9Bake range over temp.
Service modes (25)
- °F to °C conversionPress and hold the BROIL key for 5 seconds.
- 12 hour shut offPress and hold CLOCK key for 5 seconds.
- 12 Hour ShutoffPress and hold CLOCK pad for 5 seconds.
- Audible signal pitch controlPress and hold DELAY START TIME key for 5 seconds.
- Cooktop LockoutPress and hold TOP/TOP LIGHT keypad on the control panel for 5 seconds.
- Diagnostics WITH Error CodesWhile in standby, press the following keys in less than 6 seconds
- Diagnostics WITHOUT Error CodesWhile in standby, press the following keys in less than 6 seconds
- Disable/Enable all tones (except end-of-timer and error tones)Press and hold the COOK TIME key for 5 seconds.
- Disable/Enable all tones except end-of-timer and error tonesPress and hold COOK TIME key for 5 seconds.
- Disable/Enable cycle and timer-end repeating tonesPress and hold TIMER SET key for 5 seconds.
- Error History ReadEnter Service Diagnostics Cycle (1-2-3-1-2-3-1-2-3)
- Fahrenheit to Celsius conversionPress and hold BROIL key for 5 seconds.
- Fuel Type VerificationPress and hold START/ENTER key for 5 seconds. Fuel type is displayed
- Hidden EOC FunctionsPress and hold the appropriate key for 5 seconds to activate the desired hidden function. Functions…
- Manual Diagnostics Mode 1 (Full - within 120 seconds of power up)Within 120 seconds of applying power, press STOP/CLEAR, STOP/CLEAR, then START.
- Manual Diagnostics Mode 2 (Limited - after 120 seconds of power up)After 120 seconds of power up, press STOP/CLEAR, STOP/CLEAR, then START.
- Rapid Advance Mode1. Start a cycle. 2. Press HI TEMP
- Recall last failure codePress and hold the CANCEL/OFF key for 5 seconds
- Sales Demo Mode ExitRun Service Diagnostics Cycle (1-2-3-1-2-3-1-2-3) to clear Demo mode.
- Sales Demo Mode TogglePress the following key sequence in less than 3 seconds
- Sales Demonstration ModePress and hold TIMER OFF pad for 5 seconds.
- Service Diagnostics Cycle1
- Software revision numberPress and hold START/ENTER key for 5 seconds. Note
- Temperature calibration offsetPress and hold BAKE pad for 5 seconds. Current offset is shown in display (CAL shown in 4-digit…
- Verify fuel typePress and hold START/ENTER key for 5 seconds until fuel type is displayed
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool dishwasher models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax