mypros+
Error code reference

Whirlpool Washer Error Code 233

Blower Motor Inverter Fault

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 233 error code actually means

Your Whirlpool washer is showing an error because the electronic board that controls the blower motor is reporting a problem. This could be caused by a power supply issue coming into the machine or a failure of the board itself. A technician will need to test the electrical supply and inspect the components to determine the exact cause.

Diagnostic procedure

The full 233 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check line voltage to the compressor/blower motor inverter board, CN8; pin 4 to pin 1 and pin 3 to pin 1, for 102VAC-132VAC.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 233 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 233

Ranked by how often they cause this code
  1. 1Low or High Line Voltage at Inverter Board
  2. 2Failed Blower Motor Inverter Board
  3. 3Loose or Damaged Wiring at CN8 Connector
  4. 4Blower Motor Failure Loading Down the Inverter
  5. 5Intermittent Power Supply Fluctuations

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 233

What does 233 mean on a Whirlpool washer?
Error code 233 on a Whirlpool washer indicates a Blower Motor Inverter Fault. The inverter board that controls the blower motor has reported an internal fault or detected an issue with its power supply. The first step is to check that AC voltage at connector CN8 falls between 102VAC and 132VAC. If voltage is correct, the inverter board itself may need to be replaced.
Is it safe to use my Whirlpool washer when error code 233 is displayed?
You should not continue using the washer while code 233 is active. A fault in the blower motor inverter board means a key component is not operating correctly, and running the machine could worsen the damage or create an electrical hazard. Disconnect the washer from power and perform diagnostics before attempting to operate it again.
Will resetting my Whirlpool washer clear error code 233?
A power reset may temporarily clear the code if the fault was caused by a transient voltage fluctuation, but it will return if the underlying problem is not resolved. If the inverter board has an internal failure or the wiring at CN8 is damaged, the code will reappear as soon as the washer attempts to run the blower motor again. A proper electrical diagnosis should be performed rather than relying on repeated resets.
Can I fix error code 233 on my Whirlpool washer myself?
Some causes of code 233 can be addressed by a knowledgeable DIYer, such as checking that the washer is on a properly functioning circuit with voltage in the 102VAC to 132VAC range and inspecting the CN8 connector for loose or corroded pins. However, if the inverter board itself has failed, replacement requires working with line voltage components, which can be hazardous. If you are not comfortable with electrical diagnostics, a qualified appliance technician is recommended.
How much does it cost to repair error code 233 on a Whirlpool washer?
If the fix is simply addressing a wiring issue or loose connector at CN8, repair costs may be limited to a service call fee, typically in the range of $75 to $150. If the blower motor inverter board needs replacement, parts alone can run from $100 to $300 or more depending on the model, with total repair costs including labor ranging from $200 to $450. Getting a diagnostic estimate before authorizing parts is advisable.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass