mypros+
Error code reference

Whirlpool Washer Error Code F5E0

Door and door position switches do not agree (Clean mode).

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F5E0 error code actually means

Your Whirlpool washer detected that two different door sensors are giving it conflicting information about whether the door is properly closed, and this happened during the Clean cycle. The washer stops as a precaution because it cannot confirm the door is safely shut. This usually points to a problem with the door latch, one of the door sensors, or the wiring connected to them.

Diagnostic procedure

The full F5E0 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F5E0 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F5E0

Ranked by how often they cause this code
  1. 1Worn or broken door latch assembly
  2. 2Failed door switch or door position switch
  3. 3Loose or damaged wiring harness connections
  4. 4Door misalignment due to hinge wear
  5. 5Control board fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F5E0

What does F5E0 mean on a Whirlpool washer?
F5E0 means the washer's control board detected that the door switch and the door position switch are sending contradictory signals during Clean mode. The two sensors are supposed to agree on whether the door is properly closed and latched. When they disagree, the washer halts the cycle to prevent operation with an uncertain door state. This fault most often points to a problem with the door latch assembly, one of the door switches, or the wiring connecting them.
Is it safe to keep using my washer when F5E0 is displayed?
You should not run the washer in Clean mode while F5E0 is active, as the control board cannot confirm the door is safely secured. Using other wash cycles may also be unreliable if the door latch or switch is genuinely faulty. It is best to diagnose and resolve the fault before resuming normal use to avoid potential water leaks from an improperly latched door.
Will resetting my Whirlpool washer clear the F5E0 error code?
A reset may temporarily clear the F5E0 code, but the error will return if the underlying cause has not been fixed. To reset the washer, unplug it from the power outlet for one to two minutes, then plug it back in. If the door latch, switches, or wiring are faulty, the fault will reappear as soon as the washer attempts Clean mode again.
Can I fix F5E0 myself, or do I need a technician?
Some causes of F5E0 are DIY-friendly, such as reseating loose wiring connectors at the door latch. Replacing the door latch assembly or an individual door switch is also manageable for someone comfortable working with appliances and a multimeter. However, if the fault points to a control board issue or you are unsure about testing electrical components safely, calling a qualified technician is the better choice.
How much does it cost to repair a Whirlpool washer F5E0 error?
Repair costs vary depending on which component has failed. A replacement door latch assembly typically costs between $20 and $60 for the part alone. An individual door switch or position switch generally runs between $10 and $40. If you hire a technician, labor charges will add to those figures, and a control board replacement, if needed, is the most expensive outcome at potentially $150 to $350 or more for parts and labor combined.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass