mypros+
Error code reference

Whirlpool Washer Error Code F#E#

General system error code (any F#E# code not specifically listed above).

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F#E# error code actually means

Your Whirlpool washer detected an error it couldn't specifically identify and stopped the cycle as a precaution. Try turning the washer off and back on to see if the problem clears on its own. If the error comes back after restarting, a technician will need to investigate which part of the washer is causing the issue.

Diagnostic procedure

The full F#E# procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Press POWER once to clear the code. Then press POWER again to restart the washer. If the code reappears, call for service.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F#E# procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F#E#

Ranked by how often they cause this code
  1. 1Temporary power or voltage fluctuation
  2. 2Intermittent control board communication error
  3. 3Failing main control board
  4. 4Loose or damaged wiring harness
  5. 5Intermittent sensor or component fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F#E#

What does F#E# mean on a Whirlpool washer?
F#E# is a general system error category that appears when the washer's control board detects a fault it cannot match to a specific, named error code. The F and E numbers together identify which subsystem is involved, so noting the exact digits displayed is important for diagnosis. The washer stops its cycle as a precaution when this type of code appears. In many cases the fault is temporary and clears with a power reset.
Is it safe to keep using my Whirlpool washer when F#E# appears?
The washer halts the cycle when this code appears, so continuing to run a load is not possible until the code is cleared. After a successful power reset, the washer can be used normally if the code does not return. If the code repeats, avoid continued use and call for service, as a recurring undiagnosed fault could indicate an issue with the control system or another critical component.
How much does it cost to repair a Whirlpool washer showing an F#E# error?
Repair costs vary significantly depending on which component is actually at fault once a technician diagnoses the specific error. A wiring harness repair or connector reseating is generally on the lower end of the cost range, while a main control board replacement typically runs higher, often in the range of $150 to $400 or more depending on parts and labor in your area. Getting a diagnostic estimate before authorizing repairs is always recommended.
Will resetting the washer clear the F#E# error code?
Press POWER once to clear the code, then press POWER again to restart the washer. If the underlying cause was a temporary glitch such as a voltage fluctuation, the code will not return and the washer will operate normally. If the code reappears after the reset, the fault is repeatable and requires a service call to identify the specific cause.
How do I fix an F#E# error code on my Whirlpool washer?
Start by pressing POWER to clear the code, then press POWER again to restart the washer and attempt a new cycle. Check that the power cord is fully seated and that the outlet is supplying stable voltage. If the code returns, note the exact F and E numbers shown on the display and contact a qualified technician, as those specific digits point to the affected subsystem and are needed for accurate diagnosis.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass