mypros+
Error code reference

Wolf Range Error Code 1532

Right or left oven broil/left convection element DLB relay shorted (left oven).

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 1532 error code actually means

Your Wolf oven has detected an electrical problem with a safety switch that controls the broil or convection heating element in the left oven. The switch appears to be stuck in the ON position, which means the oven cannot safely control that element. This issue should be addressed by a qualified technician before using the oven again.

Diagnostic procedure

The full 1532 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 1532 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 1532

Ranked by how often they cause this code
  1. 1Shorted DLB relay on the control board
  2. 2Failed broil or convection heating element
  3. 3Damaged or shorted element wiring
  4. 4Faulty relay driver circuit on the control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 1532

What does 1532 mean on a Wolf range?
Error code 1532 means the control board has detected a shorted DLB relay in the circuit that controls the broil element or left convection element in the left oven cavity. The DLB relay is a safety relay designed to fully cut power to heating elements when they are off. A shorted relay indicates the contacts have failed in a closed state, which is a safety-relevant fault that disables normal oven operation.
Is it safe to use my Wolf oven while error code 1532 is displayed?
It is not recommended to use the oven while this error is active. A shorted DLB relay means the control board cannot reliably cut power to the broil or convection element, which could result in uncontrolled heating. Discontinue use until the fault is diagnosed and the failed component is replaced.
How much does it cost to repair a Wolf range showing error code 1532?
Repair costs depend on which component has failed. A replacement control board for a Wolf range typically falls in the range of $200 to $600 or more for the part alone, while a broil or convection element is generally less expensive, often in the $50 to $200 range. Adding professional labor costs, total repair estimates commonly run between $300 and $800 or more depending on the specific model and service provider.
Can I fix error code 1532 on my Wolf range myself?
Resolving this error typically requires replacing either the oven control board or a faulty heating element, both of which involve working with high-voltage components. A knowledgeable DIYer with experience in appliance repair can perform this work by disconnecting power and carefully inspecting the relay, wiring, and element. However, because this fault involves a safety relay, most technicians recommend professional diagnosis to confirm the exact failed component before ordering parts.
Will resetting my Wolf range clear error code 1532?
A power reset by disconnecting the range from its power source for several minutes may temporarily clear the error display, but it will not repair the underlying fault. If the DLB relay is truly shorted or the element is damaged, the error will return once the oven is powered and the control board performs its relay checks. A reset should only be used as part of the diagnostic process, not as a solution.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass