mypros+
Error code reference

Wolf Range Error Code 3031

The temperature probe is broken, socket is broken or wired wrong; probe circuit reporting below 1k ohm (right oven).

Wolf codesWolf range codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 3031 error code actually means

Error 3031 means your Wolf range has detected a problem with the temperature sensor in the right oven, specifically that the sensor or its wiring is shorted out or damaged. The oven control cannot get an accurate temperature reading, so it has shut down that function to prevent unsafe operation. A repair technician will need to test and likely replace the temperature probe, the socket it connects to, or correct the wiring.

Diagnostic procedure

The full 3031 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 3031 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 3031

Ranked by how often they cause this code
  1. 1Faulty temperature probe (internal short)
  2. 2Damaged or contaminated probe socket
  3. 3Shorted or pinched wiring harness
  4. 4Incorrect wiring from a prior repair

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 3031

What does 3031 mean on a Wolf range?
Error code 3031 indicates that the right oven temperature probe circuit is reading below 1,000 ohms, which signals a short circuit condition. This can be caused by a defective probe, a damaged probe socket, or shorted wiring in the circuit. The control board triggers this fault to alert you that it cannot reliably monitor right oven temperature. The right oven will not operate normally until the fault is resolved.
Is it safe to use my Wolf range while error 3031 is displayed?
The right oven should not be used while this error is active because the control board cannot accurately monitor that cavity's temperature. Operating the oven without a functional temperature probe creates a risk of uncontrolled overheating. Other burners or the left oven, if equipped, may still be usable, but the right oven should remain off until the probe circuit is repaired.
Will resetting the Wolf range clear error code 3031?
A power reset by turning off the circuit breaker for 30 to 60 seconds may temporarily clear the fault display, but the code will return as soon as the control board detects the low-resistance reading again. Because 3031 is caused by a hardware fault in the probe circuit rather than a software or communication glitch, the underlying component problem must be repaired before the error will clear permanently.
Can I fix error code 3031 myself?
A knowledgeable DIYer comfortable using an ohmmeter and working safely with disconnected appliances can test the probe resistance independently to determine whether the probe is at fault. If the probe tests defective, replacing it is a relatively straightforward repair. However, if the fault is in the socket or wiring harness, tracing and repairing those components typically requires more technical experience, and professional service is recommended.
How much does it cost to repair error code 3031 on a Wolf range?
If the issue is a faulty temperature probe, parts alone typically range from $30 to $100 depending on the specific model, with professional labor adding $100 to $200 or more. If the socket or wiring harness requires repair or replacement, total costs can be higher, generally in the $150 to $400 range including labor. Costs vary by region and service provider.

Related Wolf range error codes

All Wolf range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass