mypros+
Error code reference

Wolf Range Error Code E 62

Hardware error on left secondary; NTC failure.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E 62 error code actually means

Your Wolf range is detecting a problem with the temperature sensor connected to the left secondary burner. The sensor is either not working correctly or has lost its connection to the main control board. The range has shut down that burner zone as a safety precaution until the issue is resolved.

Diagnostic procedure

The full E 62 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check the NTC circuit.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E 62 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E 62

Ranked by how often they cause this code
  1. 1Failed NTC thermistor
  2. 2Damaged or broken wiring harness
  3. 3Loose or corroded connector
  4. 4Short circuit in the NTC circuit
  5. 5Control board input channel fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E 62

What does E 62 mean on a Wolf range?
E 62 indicates a hardware error in the left secondary burner's NTC thermistor circuit. The NTC thermistor is a temperature-sensing component that feeds resistance-based temperature data to the control board. When the board detects a signal outside its expected parameters, it logs E 62 and disables the affected burner zone. The fault can originate at the sensor, the wiring, or the control board itself.
Is it safe to use my Wolf range while E 62 is displayed?
E 62 disables the left secondary burner zone as part of the range's protective response to the fault, so that specific zone will not operate. Other burners may still function depending on the range's control logic. It is not advisable to continue regular use while an active fault code is present, as the underlying issue could indicate a compromised temperature-sensing circuit that may affect safe operation.
Will resetting my Wolf range clear the E 62 error?
Power cycling the range by switching it off at the breaker for a few minutes may temporarily clear the code, but if the underlying NTC circuit fault remains, E 62 will return once the range powers back up and runs its diagnostics. A reset does not repair the failed component. Proper resolution requires identifying and correcting the root cause in the NTC circuit.
Can I fix E 62 on my Wolf range myself?
A knowledgeable DIYer comfortable with multimeter testing can perform initial diagnostics, including checking wiring continuity, inspecting connectors, and testing the NTC thermistor's resistance. However, replacing components inside the range, particularly near the control board, involves working with electrical systems and should be approached carefully. If you are not confident with appliance electrical diagnostics, hiring a qualified technician is the safer choice.
How much does it cost to repair a Wolf range E 62 error?
Repair costs vary depending on which component has failed. An NTC thermistor replacement is typically the least expensive fix, with parts generally in the range of $20 to $80 and labor costs on top of that depending on your service area. If the control board requires replacement, costs can rise considerably, often ranging from $300 to $700 or more for parts and labor combined.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass