mypros+
Model reference

Amana 109-2N

Air Conditioner

57 error codes21 service modes
MyPros+ Max

Diagnose your Amana 109-2N.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (57)

CodeMeaning
1c1cShorted key detected on the membrane keyboard.1c2cMembrane keyboard disconnected.1c4cBoard-to-board communication failure.1c6cEEPROM hardware fault.1c7cControl not calibrated.1c81EEPROM CRC error in Cook Profile.1c8cEEPROM CRC error in User Options.1d11Unlocked runaway temperature condition detected at 600°F.1d21Locked runaway temperature condition detected at 950°F.3d11Temperature sensor open circuit detected.3d21Temperature sensor shorted.3d41Meat probe shorted.3d51Meat probe not calibrated.4d11Door switch not closed when door is locked.4d21No cooling fan rotation detected.4d31Cooling fan on when de-energized.4d41Cooling fan overspeed condition detected.4d51Door switch circuit fault.9d11Door latch will not lock.9d21Door latch will not unlock.9d31Door latch reporting both locked and unlocked simultaneously.F0E0No failure (GOOD)F0E2Oversuds condition detectedF0E3Overload detectedF0E4Spin limited by water temperatureF0E5Off balance load condition detected.F0E7Load detected when running Clean Washer cycleF0E8Water ringF0E9Off balance pauseF1E0Internal failure
View all 57 error codes
F1E1Internal failureF2E0Keypad disconnected.F2E1Stuck or shorted key on keypad.F2E2HMI disconnected from the ACUF3E0Main oven temperature sensor shorted or open.F3E1Lower main oven sensor shorted or openF3E2Warming drawer sensor shortedF3E3Meat probe shorted.F5E0Door and latch switch do not agree.F5E1Door latch not operating.F5E3Lid lock will not unlockF5E4Lid not opened between cyclesF6E0Lost communications between user interface and appliance manager.F6E1Cook oven over temperature.F6E2Clean oven over temperature.F6E3Mini oven/warm drawer over temperatureF6E4User interface/appliance manager mismatch.F6E5No cavity size command programmed.F7E1Tachometer missing or wrong signalF7E3Basket engaged during washF7E4Basket re-engagement failureF7E6Motor circuit openF7E7Motor unable to reach target RPM.F8E1Long fillF8E3Overflow or flood conditionF8E6Water hazardF9E1Drain pump system problem

Service modes (21)

  • Cavity size programming1
  • Clear last error code1
  • Component ActivationEnter Service Mode, navigate to Service Diagnostics, select Component Activation
  • Control LockoutPress the Back and Setup pads simultaneously for 5 seconds to lock.
  • Control Reset1
  • Demo Mode1
  • Diagnostic CycleEnter Service Mode, navigate to Service Diagnostics, select Diagnostic Cycle.
  • Diagnostic mode1
  • Display Test1
  • DLMS Calibration CycleEnter Service Mode, navigate to Factory Diagnostics, select DLMS Calibration Cycle.
  • Energy Saver Mode1
  • Fahrenheit to Celsius conversionPress OPTIONS and then '1' to toggle temperature between Fahrenheit and Celsius settings.
  • Fault HistoryEnter Service Mode, navigate to Fault History
  • Faults Access1
  • HMI TestEnter Service Mode, navigate to Service Diagnostics, select HMI Test
  • Oven temperature calibration adjustment1
  • Quick Test Mode (EOC III)1
  • Sabbath Mode activation (one-time enable)1
  • Sensor FeedbackEnter Service Mode, navigate to Service Diagnostics, select Sensor Feedback
  • Service Mode1
  • Software Versions Access1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass