Model reference
Amana 109-3F
Air Conditioner
64 error codes10 service modes
MyPros+ Max
Diagnose your Amana 109-3F.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (64)
CodeMeaning
1-1Power relay K2 stuck in closed (active) position, detected by control module.1-2Control module software problem10-1Dispenser electrical problem10-3Drying fan error2-1Stuck key detected2-2No response from user interface3-1Thermistor/soil sensor open circuit3-2Thermistor/soil sensor short circuit3-3Soil sensor (OWI) calibration failure4-3Wash motor non-operation5-1Door switch stuck open5-2Door switch stuck closed6-1No water / insufficient water level in pump (mechanical problem).6-2Fill valve electrical problem6-3Suds/air in pump6-4Overfill float switch stuck in overfill position or dishwasher not level, or…6-7Flow meter disconnected or damaged.6-8Regeneration electrical problem7-1No heat7-2Heater element stuck in active mode8-2Drain motor electrical problem8-3Drain circuit constantly powered9-1Unable to determine diverter valve position9-2Diverter valve stuck9-3Diverter disc missing9-4Lower spray arm errordrnDrain pump system problemF0E2Oversuds condition detectedF0E3Overload conditionF0E4Spin limited by water temperatureView all 64 error codes
F0E5Off balance load condition detected.F1E1Main control fault (internal ACU failure).F1E2Motor control section of the main control has faulted.F1E3Mismatch of ACU and UIF2E1UI stuck buttonF2E3UI mismatchF2E4UI software errorF2E5UI software errorF3E1Pressure system faultF3E2Inlet water temperature faultF4E1Heater stuck onF4E2Heater not turning onF5E1Lid switch faultF5E2Lid lock will not lock or lid lock failure.F5E3Lid lock will not unlock.F5E4Lid not opened between cyclesF6E2Communication errorF6E3Communication errorF7E0Loss of powerF7E1Loss of power during spinF7E2Motor drive module failureF7E3Basket engaged during washF7E4Basket re-engagement failureF7E5Shifter failure.F7E6Motor circuit openF7E7Motor unable to meet target RPM.F7E8Motor over temperatureF7E9Locked rotorF8E1Long fillF8E3Overflow or flood conditionF8E6Water hazardF9E1Drain pump system problemF9E2Drain pump system problemLFLong fill
Service modes (10)
- Customer Program Fast Forward ModeAfter starting a customer program, press HI TEMP
- Error History ClearDuring the service diagnostic program at the error display interval, press the HI TEMP (high…
- Fault Code Display / Clearing["Enter Service Diagnostic Mode.","If saved fault code exists, it will be flashing in the display…
- Key Activation & Encoder Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
- Service Calibration["Enter Service Test Mode.","Select function number 052 using Soil Level/Temp buttons or cycle…
- Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Select any three (3)…
- Service Diagnostic Program1
- Service Diagnostics (Automated Test Cycle)["Enter Service Test Mode.","Select function number 051 using Soil Level/Temp buttons or cycle…
- Service Test Mode (Load Control)["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
- Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana air conditioner models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass