mypros+
Model reference

Amana 11-5D

Air Conditioner

1 document43 error codes8 service modes

Available documentation

Tech Tip

  • Instruction Sheet24 pg
    Covers this model
MyPros+ Max

Diagnose your Amana 11-5D.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (43)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board, or incompatible software…10-1Dispenser electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control3-1Open connector or component in temperature sensing circuit (open or faulty…3-2Shorted connection or component in temperature sensing circuit, shorted or…3-3OWI calibration failure due to OWI sensor failure or drain hose check valve not…4-3Wash motor not running due to loose connection in motor circuit, faulty wash…5-1Door stuck open5-2Door stuck closed6-1Low or no water6-2Fill valve electrical problem6-3Suds or air in pump causing repeated wash periods.6-4Float switch open6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem7-1No heat7-2Heater stuck on8-2Drain motor electrical problem8-3Drain motor stuck on9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disk in sump is missing.9-4Lower spray arm errorF1E1Indicates a Cycle Control Unit (CCU) problem.F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; only…F2E2User Interface software errorF3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).
View all 43 error codes
F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms).F3E4Inlet thermistor is shorted; temperature above 391°F (<20 ohms).F3E5Inlet and exhaust thermistors are open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; only appears in service diagnostic mode.F3E7Moisture sensor strip has shorted; only appears in service diagnostic mode.F4E1No voltage detected at the heater relay; only appears in service diagnostic…F4E3Restricted/low air flow that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at installation.F6E1Communication error from UI to CCU; communication between CCU and UI has not…F6E2Communication error from CCU to UI; communication between CCU and UI has not…L2Low L2 voltage (less than 50V) detected at installation.PFPower failure occurred while the dryer was running.

Service modes (8)

  • Customer-Focused Dryness Level Adjustment1
  • Install Diagnostics1
  • Loads Test Mode1. Dryer must be in standby mode (plugged in with all indicators off). 2. Within 5 seconds: press…
  • Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Service Diagnostic Mode1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
  • Software Version Display1
  • User Interface/Control System Test1. Activate Service Diagnostic Mode. 2. Press and release the 1st button used to activate Service…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass