mypros+
Model reference

Amana 5-SPM

Air Conditioner

83 error codes23 service modes
MyPros+ Max

Diagnose your Amana 5-SPM.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (83)

CodeMeaning
1Drain time higher than 6 minutes, caused by pump failure, pressure switch…1-1Control function error1-2Control function error10-1Other10-2Other10-3Other2Water level sequence reversed during filling, caused by incorrect pressure…2-1User Interface2-2User Interface3Lower pressure switch opened during agitation, caused by user removing…3-1Thermistor/OWI3-2Thermistor/OWI3-3Thermistor/OWI4Fill is longer than 20 minutes, caused by clogged water inlet valve, damaged…4-2Wash Motor4-4Wash Motor5-1Door Switch5-2Door Switch6-1Inlet Water6-2Inlet Water6-3Inlet Water6-4Inlet Water6-6Inlet Water6-8Inlet Water7-1Heating7-2Heating8-1Draining8-2Draining8-3Draining8-4Draining
View all 83 error codes
9-1Diverter9-2Diverter9-3Diverter9-4DiverterdLLid Lock FailuredULid Unlock FailureF 1Pressure Signal Out-of-RangeF 2Keypad/User Interface FailureF 40ATC Thermistor Open/ShortF 41Motor RPS Thermistor Open/ShortF 42Heater in unknown stateF 43Heater is continuously ONF 44Heater cannot be turned ONF 50Motor StalledF 51Motor RPS FailureF 52Motor Stop FailureF 53Motor Control OvertempF 54Motor Control OvercurrentF 72Basket Re-engagement FailureF0E0No fault codes stored in memory.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected.F1E1Main control fault.F1E2Motor control fault on the main control.F1E4Microwave ACU PCBA failure.F2E1Touch panel failure.F2E3Mismatch of Main Control and User Interface; UI identification does not match…F3E1Pressure sensor fault; Main Control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected open or shorted.F4E1Cavity temperature sensor failure.F4E4Humidity sensor error.F4E9Popcorn error.F5E1Lid switch fault; lid is in locked state but lid switch is open.F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7E1Basket speed sensor fault; main control cannot determine speed of basket, or…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; open clockwise or counterclockwise circuit of the motor.F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1No fill / long fill; water level does not change for a period of time or water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Exhaust air temperature detection failure.F9E1Long drain; water level does not change after the drain pump is on for 10…HCHot, Cold ReversedLdLong DrainLFLong FilllidOpen/Close LidoLOverloadedPoPump OutSdSuds DetectionuLUnbalanced Load

Service modes (23)

  • Automatic Diagnostic Test Mode["Ensure washer is not currently running a cycle (in-progress screen should not be…
  • Automatic Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Spin LED is On (display…
  • Calibration Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Rinse LED is On (display…
  • Component Tests["Enter the Service Routine first.","Step 1
  • Console and Indicators Diagnostic Test Mode["Ensure washer is not currently running a cycle and LCD is on.","Press Power/Cancel button and…
  • Diagnostic / Test Mode["Plug in microwave oven or reconnect power.","Press CANCEL button to reach Standby mode (colon ':'…
  • Diagnostics / Test Mode["Plug in microwave oven or reconnect power.","Press the Cancel keypad to reach standby display…
  • Error Code Display (within Service Diagnostics)After entering Service Diagnostics Cycle, errors are displayed in intervals 25-22. Interval 27
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Done LED is On (display…
  • Last Error Display["Enter the Service Routine first.","Simultaneously press the WATER LEVEL and PROGRAM SELECTION…
  • LED Test["Enter the Service Routine first.","Press the WATER TEMPERATURE keypad and all of the LEDs should…
  • Manual Diagnostic Test Mode["Perform steps 1 and 2 of Activation of Automatic Diagnostic Test Mode (Sound and Display >…
  • Manual Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Spin and Done LEDs are On…
  • Pressure Transducer Calibration["Enter Manual Diagnostic Test Mode.","From the Component Activation screen, select the 'Pressure'…
  • Rapid Advance ModeAfter starting a cycle, press HI TEMP
  • Saved Fault Codes["Enter Service Mode (Sound and Display > Service Mode > 5, 6, 5, 6 within 5 seconds >…
  • Service Diagnostic Test Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Service Diagnostics Cycle1
  • Service Routine["Make sure the washer is turned off while it is plugged into a power outlet.","Disconnect the…
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Rinse, Spin, and Done LEDs…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Wash and Done LEDs are On…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Rinse and Spin LEDs are On…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass