mypros+
Model reference

Amana 5P-2JM/P54360-33R

Air Conditioner

40 error codes13 service modes
MyPros+ Max

Diagnose your Amana 5P-2JM/P54360-33R.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (40)

CodeMeaning
13EMAIN PCB signal not detected for 10 seconds.3EMotor failure4EWater level sensor fault5ENo drain8EMotor faultCEWater temperature faultdoorDoor is open and washer is paused.E0Sub-code used with F1 (EEPROM communications), F2 (UL A/D errors), F3 (oven…E1Sub-code used with F1 (EEPROM checksum failure), F2 (shorted keypad/cable…E2Sub-code used with F3 indicating bake range over-temperature.E3Sub-code used with F3 indicating clean range over-temperature.F0No failure has occurred (displayed when most recent F-code is recalled via user…F1EEPROM communications or EEPROM checksum failure in the electronic oven control.F1 E0EEPROM communication error.F1 E1EEPROM checksum error.F1 E2A/D converter error (possible lost voltage rail).F1 E5Calibration shifted.F1 E9Stack overflow.F2Shorted keypad or keypad cable unplugged (UL A/D errors).F2 E0Shorted key / key stuck.F2 E1Keypad / keytail not connected.F2 E5Cancel key low or open.F3Oven sensor opened, oven sensor shorted, bake range over-temperature, or clean…F3 E0Temperature sensor open.F3 E1Temperature sensor shorted.F3 E2Non-self-clean over temperature (usually 550°F).F3 E3Self-clean over temperature (usually 900°F).F5Door and latch switches do not agree, solenoid not operating, latch switch…F5 E0Latch switch does not agree with door switch (latch in locked position with…F5 E1Latch will not lock.
View all 40 error codes
F5 E5Self-clean temperature set point not reached within required time range…F5 E7Latch will not unlock.HE1Heater is over heatingHE2Heater is not heatingIEPressure switch errorLENo fillOEWater sensor level faultPFPower failuretESump thermistor failureUEUnbalance detected during final spin

Service modes (13)

  • Abbreviated White/Cottons Cycle TestWhile in Service Mode, press Delay Start (four times) followed by Start/Pause button.
  • Board Output Test (EEPROM Test)Press and hold the Rinse, Prewash and Delay Start buttons, followed by the Power On/Off switch
  • Board Output Test (EEPROM)Press and hold Rinse, Prewash and Delay Start, then press Power On/Off switch
  • Component TestWhile in Service Mode, press the Start/Pause button to cycle through
  • LED/Switch TestEnter the Board Output Test, then press the Temperature key (three times) followed by Start/Pause…
  • Motor Output TestEnter the Board Output Test, then press the Temperature key (twice) followed by Start/Pause button
  • Oven Temperature Calibration["Touch and hold the BAKE keypad for 4 seconds.","The display will indicate the present oven…
  • Rinse And Spin TestWhile in Service Mode, press Delay Start (seven times) followed by Start/Pause button
  • Service Mode1
  • Spin TestWhile in Service Mode, press Delay Start (six times) followed by Start/Pause button
  • Thermistor TestWhile in Service Mode, press Delay Start (two times) followed by Start/Pause button
  • Unbalance TestWhile in Service Mode, press Delay Start (three times) followed by Start/Pause button
  • White/Cottons Cycle TestWhile in Service Mode, press Delay Start (five times) followed by Start/Pause button.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass