mypros+
Model reference

Amana CRH5-1/P58372-28C

Air Conditioner

62 error codes28 service modes
MyPros+ Max

Diagnose your Amana CRH5-1/P58372-28C.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (62)

CodeMeaning
1c1cShorted key detected on the control circuit board keyboard.1c2cKeyboard tail disconnected or keyboard loop has improper value.1c31Cancel key circuit problem (cancel key improper value) on upper/single oven…1c32Cancel key circuit problem (cancel key improper value) on lower oven cavity.1c4cPower micro communication failure (CRC invalid).1c6cEEPROM error1c7cControl not calibrated1c81Cook profile corrupted in EEPROM for upper/single oven cavity (CRC invalid).1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC invalid).1d11Runaway temperature (650°F) detected with door unlocked on upper/single oven…1d12Runaway temperature (650°F) detected with door unlocked on lower oven cavity.1d21Runaway temperature (950°F) detected with door locked on upper/single oven…1d22Runaway temperature (950°F) detected with door locked on lower oven cavity.3d11Temperature sensor failure (open) on upper/single oven cavity3d12Temperature sensor failure (open) on lower oven cavity3d21Temperature sensor failure (short) on upper/single oven cavity3d22Temperature sensor failure (short) on lower oven cavity3d41Meat probe shorted3d51Meat probe not calibrated4d11Door switch position failure4d12Door switch position failure4d21No Reverse Airflow Fan rotation (no/low RPM) on upper/single oven cavity.4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven cavity.4d31Reverse Airflow Fan state error4d32Reverse Airflow Fan state error4d41High Reverse Airflow Fan rotation (high RPM) on upper/single oven cavity.4d42High Reverse Airflow Fan rotation (high RPM) on lower oven cavity.4d51Door switch circuit failure4d52Door switch circuit failure9d11Door latch will not lock on upper/single oven cavity
View all 62 error codes
9d12Door latch will not lock on lower oven cavity9d21Door latch will not unlock on upper/single oven cavity9d22Door latch will not unlock on lower oven cavity9d31Door latch both locked and unlocked simultaneously on upper/single oven9d32Door latch both locked and unlocked simultaneously on lower ovenAFRestricted/low air flow detected that may affect dryer performance.F1E1Indicates a Cycle Control Unit (CCU) problem.F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; only…F2E2User Interface Software Error 1F2E3User Interface Software Error 2F3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms)F3E4Inlet thermistor is shorted; temperature above 760°F (<20 ohms)F3E5Inlet and exhaust thermistors are both open; will occur if P14 connector is not…F3E6Moisture sensor strip is openF3E7Moisture sensor strip has shortedF4E1No voltage detected at the heater relayF4E3Restricted air flow detected that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.F6E1Communication between the CCU and UI has not been detected (UI to CCU).F6E2Communication between the CCU and UI has not been detected (CCU to UI).FCE0Communication error between ECM and CCU (model WEL98 only).FCE1Communication error from dryer to wireless router (model WEL98 only).FCE2Wireless router cannot communicate with the internet (model WEL98 only).FCE3Antenna A (J2) is bad (model WEL98 only).FCE4Antenna B (J11) is bad (model WEL98 only).FCE5Current Transformer A not functioning at J12 (model WEL98 only).FCE6Current Transformer B not functioning at J12 (model WEL98 only).FCE7Provisioning failureL2Low L2 voltage (less than 50V) detected at the CCU.PFPower failure occurred while the dryer was running.

Service modes (28)

  • 24-Hour Clock TogglePress and hold CANCEL and DELAY pads for 3 seconds
  • Child Lockout (Control Lock)Press and hold CANCEL and COOK & HOLD pads for 3 to 5 seconds until beep sounds.
  • Clock Display TogglePress and hold CANCEL and CLOCK pads for 3 to 5 seconds.
  • Component ActivationFrom Service Diagnostics Diagnostics Home screen, select 'Component Activation'
  • Customer-Focused Dryness Level Adjustment1. Turn cycle selector knob to an automatic cycle. 2. From the Automatic Cycle Main Screen, press…
  • Diagnostic Code Display Mode1
  • Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
  • Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
  • Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
  • Factory Default ResetPress and hold CANCEL and KEEP WARM pads for 3 to 5 seconds.
  • Faults Access (EOC III Controls)1
  • One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
  • Oven Temperature Adjustment (Hidden Function)1
  • Quick Diagnostic TestFrom Diagnostics Home screen, select 'Error Diagnostic', then select 'Quick Diagnostic Test'
  • Quick Test Mode1. Press and hold CANCEL and BROIL pads for 3 seconds. 2. Once the control has entered Quick Test…
  • Quick Test Mode (EOC III Controls)1
  • Quick Test Mode (H1 Controls - Convection Model)1
  • Quick Test Mode (H1 Controls - Non-Convection Model)1
  • Quick Test Mode (H2/H2.5 Controls)1
  • Quick Test Mode (H3 Controls)1
  • Quick Test Mode (M1/M2 Controls)1
  • Quick Test Mode (NSC Non-Self Clean Controls)1
  • Sabbath ModeHold CLOCK pad for 3 to 5 seconds to activate Sabbath mode.
  • Service Diagnostics1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Service Mode (EOC III Controls)1
  • Temperature Display Toggle (°F/°C)Press and hold CANCEL and BAKE pads for 3 to 5 seconds
  • Test Mode (UH Controls)1
  • UI Component TestFrom Diagnostics Home screen, select 'Component Activation', then select 'UI Component Test'

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax