mypros+
Model reference

Amana DCS-215-1H

Dishwasher

3 documents57 error codes64 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11696830 - Rev A21 pg
    Covers this model
  • Tech Sheet - W10404629 - Rev B20 pg
    Covers this model
  • Basic Operation of Commercial Stacked Washer/dryer20 pg
    Covers this model
MyPros+ Max

Diagnose your Amana DCS-215-1H.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (57)

CodeMeaning
d 13Coin 2 errord 16Generation 2 debit card reader errord13Coin 2 errord16Generation 2 debit card reader errord2Dryer exhaust thermistor shorted errord22Dryer Generation 2 debit card reader errord23Dryer communication failure from dryer CCU to UICd3Dryer exhaust thermistor open errord36Stuck key errord4Dryer motor control circuit errord5Coin 1 errord7Dryer UIC microprocessor errord8Dryer UIC EEPROM errord9Low voltage detection errorF 01Dryer motor control circuit errorF 04Accelerometer failureF 11MCU errorF 20No water detected entering washerF 21Long drainF 22Door lock errorF 23Dryer exhaust thermistor shorted errorF 24Temperature sensor errorF 25Tachometer errorF 26Door switch errorF 27Overflow conditionsF 28Communication failure between CCU and MCU.F 29Door unlock errorF 31Overheating of motorF 33Pump disconnectedF 34Load detected in washer during Washer Cleanout Cycle.
View all 57 error codes
F 70Communication failure between CCU and UIC.F 71Dryer communication failure from UIC to dryer CCUF 73UIC failure (washer) / UIC Microprocessor error (dryer)F 74UIC EEPROM errorf01Dryer motor control circuit errorF03Accelerometer failureF04Accelerometer failureF11MCU errorF20No water detected entering washerF21Long drainf22Dryer exhaust thermistor openf23Dryer exhaust thermistor shortedF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionsF28Communication failure between CCU and MCU.F29Door unlock errorF31Overheating of motorF33Pump disconnectedF34Load detected in washer during washer cleanout cycle.F37Water level out of range lowF38Water level out of range highf70Communication failure from dryer CCU to UICf71Communication failure from UIC to dryer CCUf73UIC microprocessor errorf74UIC EEPROM error

Service modes (64)

  • Clean Washer Program["Enter Diagnostic Mode (display flashing).","Press the COLORS/DELICATES button."]
  • Code Display Mode["For 9150 Models
  • Cycle Credit["Enter Flashing Mode (entire display flashing).","Press the HOT button (CC will display)."]
  • Diagnostic Mode["First enter 'Start Operating Set-Up' (set-up mode).","Press and hold the lower right (QUICK…
  • Diagnostic Mode (Washer Diagnostic Mode)["First access the Setup Mode (Start Operating Set-up).","Press the QUICK CYCLE button for 1 second…
  • Dryer Field Diagnostic Cycle["Enter Diagnostic Mode.","With the entire display flashing, press the upper middle (PERM
  • Dryer Field Diagnostic Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM PRESS) button."]
  • Free Cycle Credit["Enter Diagnostic Mode (display flashing).","Press the HOT button to credit one free cycle…
  • Help Mode["For PD models
  • Help Mode (dAS mode)["Enter set-up mode.","The message dAS will appear in the display.","Press the HOT button.","Press…
  • Help Mode (Manual Communication)["Enter set-up mode.","Press the WARM button until set-up code 2.XX is on display.","Press the HOT…
  • Help Mode (PD Models)1) Open service door
  • Manual Overview Test["Enter Diagnostic Mode (flashing display).","Press WHITES button."]
  • P-01 Cancel Cycle, Reset Errors, and Clear EscrowFrom diagnostic test modes, navigate to P-01 display and press START
  • P-02 Cycle CreditFrom diagnostic test modes, navigate to P-02 display and press START
  • P-03 Quick Overview TestFrom diagnostic test modes, navigate to P-03 display and press START
  • P-04 Manual Overview TestFrom diagnostic test modes, navigate to P-04 display and press START
  • P-05 Button TestFrom diagnostic test modes, navigate to P-05 display and press START. TEST will be displayed. Press…
  • P-06 Drain and SpinFrom diagnostic test modes, navigate to P-06 display and press START
  • P-07 UI DiagnosticsFrom diagnostic test modes, navigate to P-07 display and press START
  • P-08 Clean Washer CycleFrom diagnostic test modes, navigate to P-08 display and press START
  • P-09 Factory DiagnosticsFrom diagnostic test modes, navigate to P-09 display and press START.
  • P-10 Dryer Diagnostic Cycle["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until 'P-10' is displayed.","Press…
  • Quick Overview Test["Enter Diagnostic Mode (flashing display).","Press DELICATES AND KNITS button."]
  • Quick Spin Cycle["Enter Flashing Mode (entire display flashing).","Press the PERM PRESS button."]
  • Quick Spin Program["Enter Diagnostic Mode (display flashing).","Press the PERM PRESS button."]
  • Quick Spin/Drain Program["Enter Diagnostic Mode (flashing display).","Press COLORS button."]
  • Service Access CodeOnly functions on washers set up for 0 vend price without Special Pricing and Coin/Debit Option set…
  • Service Access Code (for PN models without key switch)["Works only on washers configured for $0.00 selling price without Special Price option, and…
  • Service Access Code (Technician key dance)Only available on washers set to free vend (6 00) with no Special Pricing and Coin/Debit Option set…
  • Service Access Code (Technician)Only works on washers set to free vend (6 00) with no Special Pricing and Coin/Debit Option set to…
  • Service Access Code Mode["1
  • Service Diagnostic Test Mode["Enter service mode (setup mode) so the display shows either 6.xx code, cycle count, money count…
  • Service Diagnostic Test Modes1) Turn off power, remove service door on metercase models or remove AA1 Service/Coin Jumper from…
  • Service/Set-up Mode (PD Models)Insert service access door key, turn, and lift to remove service access door
  • Service/Set-up Mode (PR Models via AA1 jumper)1
  • Service/Set-up Mode (PR Models)Insert a set-up card (supplied by reader manufacturer) into the card slot
  • Service/Setup Mode (PD Models)["Insert service access door key, turn, and lift to remove service access door.","Display will show…
  • Service/Setup Mode (PR Models via AA1 connector)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
  • Set-Up Mode["PD/PN Models
  • Set-Up Mode (9150 Models)["Insert access door key, turn, and lift to remove access door."]
  • Set-Up Mode (9160 Models)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
  • Set-Up Mode (Coin Payment)["Insert service switch key and turn counter-clockwise."]
  • Set-Up Mode (PD Models)Insert service access door key, turn, and lift to remove service access door
  • Set-Up Mode (PR Models)Install debit card reader per manufacturer instructions, then insert a set-up card (supplied by…
  • Setup Mode["PD/PR Models
  • Setup Mode (Configuration Mode) - Model 9150["Insert the service door key, turn and lift to remove the access door."]
  • Setup Mode (Configuration Mode) - Model 9160["Disconnect the washer from power.","Open the console and disconnect connector AA1.","Close the…
  • Setup Mode (PD Models)Insert service access door key, turn, and lift to remove service access door
  • Setup Mode (PR Models)Insert a set-up card (from reader manufacturer) into the card slot. If no set-up card is available…
  • Setup Mode (Programming Mode)["For PD models
  • Technician Service Access CodeOnly available on washers set to free vend (6 00) with no Special Pricing set-up, and Coin/Debit…
  • Technician Service Access Code (free vend models only)["Washer must be set to free vend (6 00), no Special Pricing, Coin/Debit Option set to…
  • Washer Cleaning Program["Enter Diagnostic Mode (flashing display).","Press BRIGHTS button."]
  • Washer Cleanout Cycle["Enter Flashing Mode (entire display flashing).","Press the COLORS/DELICATES button."]
  • Washer Cleanout Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center right (COLORS/DELICATES)…
  • Washer Cycle Credit (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower left (HOT) button (CC will…
  • Washer Diagnostic Mode (Flashing Mode)["First enter Set-Up Mode.","Press and hold the COLD button for 2 seconds while in set-up code 6…
  • Washer Manual Overview Test Cycle["Enter Diagnostic Mode.","With the entire display flashing, press the center left (WHITES)…
  • Washer Manual Overview Test Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center left (COTTON/WHITES) button."]
  • Washer Quick Overview Test Cycle["Enter Diagnostic Mode.","With the entire display flashing, press the lower middle (DELICATES AND…
  • Washer Quick Overview Test Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (WARM) button."]
  • Washer Quick Spin Cycle["Enter Diagnostic Mode.","With the entire display flashing, press the center middle (COLORS)…
  • Washer Quick Spin Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center middle (PERM PRESS) button."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax