mypros+
Model reference

Amana DCS211-1H

Dishwasher

4 documents84 error codes32 service modes

Available documentation

Tech Sheet

  • Basic Operation of Commercial Stacked Washer/dryer20 pg
    Covers this model
  • Tech Sheet - W103503332 pg
    Covers this model
  • Whirlpool Dishwasher WDF530PLYW0 Tech Sheet2 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 85244282 pg
    Covers this model
MyPros+ Max

Diagnose your Amana DCS211-1H.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (84)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board or incompatible software…1-3Control detected stuck key(s) in keypad or keypad connection.10-1Dispenser electrical problem10-2Vent wax motor electrical problem.10-3Drying fan error2-1User interface stuck key or short circuit(s) in keypad or in control's input…2-2Software or hardware incompatibility problem with control.3-1Open temperature sensing circuit3-2Shorted temperature sensing circuit3-3OWI/thermistor sensor failed calibration.4-3Wash motor not running5-1Door stuck open5-2Door stuck closed6-1Inlet water6-2Inlet water6-3Inlet water6-4Inlet water6-6Inlet water6-7Disconnected or damaged flowmeter.6-8Inlet water7-1Heating7-2Heating8-1Draining8-2Draining8-3Draining9-1Diverter9-2Diverter stuck on9-3Diverter disk missing from sump.C1Blocked coin 1 or coin drop control circuit failure (coin recognition and price…
View all 84 error codes
C2Blocked coin 2 or coin drop control circuit failure (coin recognition and price…d 13Coin 2 errord 16Generation 2 debit card reader errord13Coin 2 errord16Generation 2 debit card reader errord5Coin 1 errord9Low voltage detection errorEdNot receiving communications from installed debit card reader in Enhanced…F 01Dryer motor control circuit errorF 04Accelerometer failureF 11MCU errorF 20No water detected entering washerF 21Long drainF 22Door lock errorF 23Dryer exhaust thermistor shorted errorF 24Temperature sensor errorF 25Tachometer errorF 26Door switch errorF 27Overflow conditionsF 28Communication failure between CCU and MCU.F 29Door unlock errorF 31Overheating of motorF 33Pump disconnectedF 34Load detected in washer during Washer Cleanout Cycle.F 70Communication failure between CCU and UIC.F 71Dryer communication failure from UIC to dryer CCUF 73UIC failure (washer) / UIC Microprocessor error (dryer)F 74UIC EEPROM errorF01CCU (Central Control Unit) errorF04Accelerometer failureF11MCU (Motor Control Unit) errorF20No water detected entering washerF21Long drainF22Door lock errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between CCU and MCU.F29Door unlock errorF31Overheating of motorF33Pump disconnectedF34Load detected in washer during Washer Cleanout Cycle.F70Communication failure between CCU and UI (User Interface).F73UI failureF74UI failureLdWasher lid sense error on control board or due to power line interference…LFWater level detection error on control board or due to power line interference…LSMotor sense error detected on control board or due to power line interference.LVVoltage detected below 90 VAC for 8 seconds.SdLast drain occurring during final spin was slow.SFLast fill was slow.SudSSuds detected during draintFWater temperature sense error when equipped with temperature sensing water…

Service modes (32)

  • diagnostic mode["Enter set-up mode first.","While in any of the set-up codes 1 through 6, anytime a diagnostic…
  • Diagnostic Mode (Washer Diagnostic Mode)["First access the Setup Mode (Start Operating Set-up).","Press and hold the QUICK CYCLE button for…
  • Dryer Field Diagnostic Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM PRESS) button."]
  • Error History ReadingEnter Service Diagnostics Cycle. Error codes are displayed in intervals 24 (Error 1
  • field diagnostic cycle["Enter diagnostic mode (entire display flashing).","Press the LOWER MIDDLE key pad to start the…
  • help mode["Enter set-up mode first.","Navigate to special pricing option mode (code 2.XX).","Press the LOWER…
  • Help Mode (Aide Mode)["PD models
  • Help Mode (dAS Mode)["Open the service door or insert a manual diagnostic card.","The message 'dAS' will appear in the…
  • Help Mode (PD Models)["Open the service door.","Press the LOWER MIDDLE key pad until the display reads 2.XX.","Press the…
  • Manual Overview Test["Enter Diagnostic Mode (display is flashing).","Press the WHITES button."]
  • Quick Overview Test["Enter Diagnostic Mode (display is flashing).","Press the DELICATES AND KNITS button."]
  • Quick Spin Program (Drain and Spin)["Enter Diagnostic Mode (display is flashing).","Press the COLORS button."]
  • Rapid Advance Mode (Cycle Operation)After starting a cycle, press HI TEMP
  • Rapid Advance Mode (during active cycle)Press HI TEMP
  • Rapid Advance Mode (in-cycle)After starting a cycle, press HI TEMP
  • Service Access Code (Code d'accès pour entretien)["Works only on washers configured for $0.00 sale price without Special Price, and Coin/Debit…
  • Service Access Code (key dance entry without console removal)["Washer must be set up for 0 vend price without Special Pricing, and Coin/Debit Option must be set…
  • Service Access Code (Key Dance)["Open the door.","Press the upper left key pad.","Press the lower right key pad.","Press the upper…
  • Service Diagnostic Test Modes["Make sure power is turned off.","Remove the service door on metercase models, or remove the AA1…
  • Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
  • Service Diagnostics Error History ReadoutAfter entering Service Diagnostics Cycle, errors are displayed in intervals 24 (Error 1
  • set-up mode["PD Models
  • Set-Up Mode (Coin Payment)["Insert service switch key and turn counter-clockwise."]
  • Set-up Mode (PD Models)["Insert service access door key, turn, and lift to remove service access door."]
  • Set-up Mode (PR Models via AA1 removal)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
  • Setup Mode (Parameter Setting Mode)["PD models
  • Washer Cleaning Program["Enter Diagnostic Mode (display is flashing).","Press the BRIGHTS button."]
  • Washer Cleanout Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center right (COLORS/DELICATES)…
  • Washer Cycle Credit (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower left (HOT) button (CC will…
  • Washer Manual Overview Test Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center left (COTTON/WHITES) button."]
  • Washer Quick Overview Test Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (WARM) button."]
  • Washer Quick Spin Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center middle (PERM PRESS) button."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax