Model reference
Amana GH-160-5
Furnace
4 documents62 error codes15 service modes
Available documentation
Tech Sheet
- techsheet-w10254504-reva56 pg
- Tech Sheet - W11503313 - Rev A2 pg
- Wiring Sheet - W11336175 - Rev A2 pg
- Tech Sheet - RT532001214 pg
MyPros+ Max
Diagnose your Amana GH-160-5.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (62)
CodeMeaning
DoorDoor Interlock Primary Switch error.Err1Failed H.VErr2Failed H.VErr3Failed H.VErr4Failed H.VErr5Failed Touch Panel (touch panel pressed for more than 30 seconds triggers this…Err6Failed H.VErr7Error with RTD circuitF0 E0Factory defaultF01Oven temperature sensor circuit is open.F02Welded (stuck closed) heating element relays detected.F05Door or latch mechanism problem.F06Electronic control malfunction.F0E1Load detected during the washer cleaning cycleF1 E0EEPROM communications error.F1 E1EEPROM checksum error.F1 E2UL A/D error(s).F1 E4Model ID error.F1 E6Latch signal mismatch error.F1E1A/D (Analog to Digital) error(s) in the control board.F1E2Shorted keypad detected.F2 E0Shorted key.F2 E1Key tail unplugged.F2E2User Interface (UI) software errorF2E3Unsupported CycleF3 E0Oven sensor openedF3 E1Oven sensor shortedF3 E2Bake range over temperature.F3 E3Clean range over temperature.F3 E4Oven sensor openedView all 62 error codes
F3 E5Oven sensor shortedF3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3E0Main oven sensor open or shorted.F3E1Pressure Switch / Pressure Sensor ErrorF3E2Temperature Sensor ErrorF3E4Level or presence sensor errorF4E0Heater is not detectedF5 E0Door switches do not agree.F5 E1Door latch not operating.F5E0Door and switches do not agree (Clean modeF5E1Door Switch ErrorF5E2Door Lock ErrorF5E3Door Unlock ErrorF6E1Communication Error between CCU and MCUF6E2Communication Error UI to CCUF6E3Communication Error CCU to UIF6E5Communication error between CCU and Expansion Board (EB)F7E1Drive Motor Tachometer Error / Washer OverloadF7E2MCU Fault or Motor OverheatF8 E0Not specified (listed as N/A).F8E0Steam Inlet Valve ErrorF8E1No water detected entering washer or pressure switch trip not detectedF8E2Dispenser System ErrorF8E3Overflow ConditionF8E4Flow Meter FaultF9E0Mis-wired house or range electrical connection.F9E1Long DrainHOTOven overtemperature conditionPFPower failure indication; blinks in the display after a power outage longer…SudSuds detectedSUDSSuds detected
Service modes (15)
- Auto TestFollow steps 1 through 4 to run Auto Test
- Automatic Function TestWith door latched, press key pads in the following sequence within 10 seconds
- Clear Fault Codes1
- Convection Temperature Calibration["Door must be closed.","Press HIDDEN PAD.","Press pads 1, 3, 5, 7, 9.","Press '0' pad to view…
- Diagnostic ModePress CANCEL > CANCEL > START within 5 seconds.
- Fault Code Display1
- Fault/Error Code Display["Activate Service Diagnostic Mode first.","Press and release the 3rd button used to activate…
- Manual Function TestWith door latched, press key pads in the following sequence within 10 seconds
- Power Test (Traditional Test Method)["Place one rack in oven using lowest rack position.","Fill plastic container to bottom of 1000 ml…
- Quick Diagnostic Test["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
- Quick Diagnostics1
- Service Diagnostic Mode1. Ensure washer is in standby mode (plugged in with all indicators off). 2. Select any three…
- Service Test Mode["Oven must be in STANDBY mode with door closed.","Press Hidden Pad.","Press pads 1, 3, 5, 7…
- Software Version Display1
- User Interface Test1
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana furnace models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass