Model reference
Amana GL-200E/P96302-8F
Furnace
14 documents18 error codes13 service modes
Available documentation
Tech Sheet
- Tech Sheet - W11087920 - Rev A60 pg
- Tech Sheet whirlpool dryer W10606148 Rev C60 pg
- Tech Sheet - W10403269 - Rev A52 pg
Installation Guide
- Installation Instructions64 pg
- Installation Instructions80 pg
- Installation Instructions68 pg
- Instrucciones de instalacion116 pg
- Installation Instructions17 pg
- Installation Instructions7 pg
- Installation Instructions56 pg
- Installation Instructions8 pg
- Installation Instructions24 pg
- Installation Instructions7 pg
Quick Reference
- Quick Reference Manual4 pg
MyPros+ Max
Diagnose your Amana GL-200E/P96302-8F.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (18)
CodeMeaning
F1E1Indicates a Cycle Control Unit (CCU) problem.F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; only…F2E2User Interface software errorF3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms).F3E4Inlet thermistor is shorted; temperature above 391°F (<20 ohms).F3E5Inlet and exhaust thermistors are open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; only appears in service diagnostic mode.F3E7Moisture sensor strip has shorted; only appears in service diagnostic mode.F4E1No voltage detected at the heater relay; only appears in service diagnostic…F4E3Restricted/low air flow that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at installation.F6E1Communication between CCU and UI has not been detected (UI to CCU communication…F6E2Communication between CCU and UI has not been detected (CCU to UI communication…FCE1WiFi Module communications lost.L2Low L2 voltage (less than 50V) detected at installation.PFPower failure occurred while the dryer was running.Service modes (13)
- Component Activation / Quick Service Cycle (LCD in Door Models)["Enter Service Diagnostic Mode (LCD in Door) first.","From the DIAGNOSTICS HOME screen, scroll…
- Customer-Focused Dryness Level Adjustment1
- Install Diagnostics1
- Key Activation & Encoder Test (Console Models)["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
- Loads Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds: Press…
- Service Diagnostic Mode1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
- Service Diagnostic Mode (Console Models)["Ensure the dryer is in standby mode (plugged in with all indicators off).","Select any three (3)…
- Service Diagnostic Mode (LCD in Door Models)["Ensure the dryer is in standby mode (plugged in with all indicators off).","Open and close the…
- Service Test Mode (Console Models)["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
- Software Version Display1
- Software Version Display (Console Models)["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
- User Interface Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
- User Interface/Control System Test1. Activate Service Diagnostic Mode. 2. Press and release the 1st button used to activate Service…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana furnace models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass