Model reference

Amana OC-100/P96290-1F

Name: Amana OC-100/P96290-1F
Brand: Amana

Furnace

1 document61 error codes8 service modes

Available documentation

Tech Sheet

W10751162A.fm12 pg
Covers this model

MyPros+ Max

Diagnose your Amana OC-100/P96290-1F.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Amana Furnace

1-1 on my Amana OC-100/P96290-1F

M+

Control function error - Pilot relay

From Tech Sheet W14436633, p.45:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (61)

View all 61 error codes

F1-E1Control detected K2 pilot relay stuck closed.F1-E2Damaged or corrupted memory on control board; incompatible software components…F10-E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.F1E1Primary control failure indicating the machine control electronics has failed.F2-E1Control detected stuck key(s) in keypad or keypad connection.F2-E2User interface cannot communicate with main control; loose user interface…F2E1Stuck button or user interface mismatch; this fault code will ONLY appear when…F3-E1Open connector or component in temperature sensing circuit; open or faulty…F3-E2Incoming water temperature above 167°F (75°C), or shorted connection/component…F3-E3OWI calibration failure; dirty water backs into dishwasher after draining or…F3E1Exhaust thermistor is open.F3E2Exhaust thermistor has shorted.F3E6Moisture sensor strip is open; this fault code will ONLY appear when in the…F3E7Moisture sensor strip has shorted; this fault code will ONLY appear when in the…F4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F5-E1Door stuck open; door was not latched within 4 seconds of pressing…F5-E2Door stuck closed; control programmed to not start if it suspects the door…F6-E1Low/no water to dishwasher (mechanical problem).F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds/air in pump; too many suds, captured wash water, or water leaking from…F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Flowmeter disconnected or damaged.F6-E8Water softener regeneration valve electrical problem; loose connection in regen…F7-E1No heat; control programmed to disable heater if it detects a water heating…F7-E2Heater stuck on; heater drive circuit on the control.F8-E1Slow drain; obstructed drain hose or path.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain stuck on; drain motor drive circuit on the control.F8E1No voltage is detected at the water valve relay (only appears in service…PFA power failure occurred while the dryer was running.

Service modes (8)

Customer Cycle Rapid Advance["Start a customer cycle.","Press HIGH TEMP
Customer-Focused Drying Mode Adjustment["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the DONE…
Error Code Display (within Service Diagnostics)After entering Service Diagnostics Cycle, errors are displayed in intervals 25-22. Interval 27
Error Code Display and Clear["Enter Service Diagnostics Cycle (1-2-3-1-2-3-1-2-3).","Interval 24
Rapid Advance ModeAfter starting a cycle, press HI TEMP
Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the DONE…
Service Diagnostics Cycle1
User Interface/Control System Test["First activate Service Diagnostic Mode (see above).","Press and release the 1st button used to…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass