Model reference
Amana YY-80-MA
Furnace
4 documents42 error codes21 service modes
Available documentation
Tech Sheet
- Tech Sheet - 97603318 pg
Service Manual
- service manual W1133862052 pg
Tech Tip
- Instruction Sheet - 85290016 pg
- Instruction Sheet - 3979706 - Rev A8 pg
MyPros+ Max
Diagnose your Amana YY-80-MA.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (42)
CodeMeaning
E0Manufacturing codeE1Manufacturing codeE2Manufacturing codeE3Manufacturing codeE4Ice maker errorE5Ice maker errorE6Manufacturing codeErManufacturing codeF0-E0No failureF0E0No failure (displayed only if user presses and holds CANCEL/OFF key for 5…F1-E0EEPROM communications failure.F1-E1EEPROM checksum failure.F1-E3Fuel type (gas/electric) select failure.F1E0EEPROM communications failure.F1E1EEPROM checksum failure.F1E3Fuel type (gas/electric) select failure.F1E4Microwave ACU PCBA failure.F2-E0Key held down too long or shorted key.F2-E1Keytail unplugged or damaged.F2-E6CANCEL key failure.F2E0Key held down too long or shorted key.F2E1Keytail unplugged or damaged.F2E6CANCEL key failure.F3-E0Oven sensor opened.F3-E1Oven sensor shorted.F3-E2BAKE/BROIL range over temperature.F3-E3CLEAN range over temperature.F3E0Oven sensor opened.F3E1Oven sensor shorted.F3E2BAKE/BROIL range over temperature.View all 42 error codes
F3E3CLEAN range over temperature.F4E1Cavity temperature sensor (FC NTC) failure.F4E4Humidity sensor error.F4E9Smart pop error.F5-E0Door switches do not agree.F5-E1Door latch not operating.F5-E2Latch error during CLEAN.F5E0Door switches do not agree.F5E1Door latch not operating.F5E2Latch error during CLEAN.F6E0ACU PCBA communication failure.F8E5Exhaust air temperature detection failure from Hood NTC thermistor.
Service modes (21)
- 12 hour shut offPress and hold CLOCK pad for 5 seconds.
- 12 Hour Shut-off TogglePress and hold CLOCK key for 5 seconds.
- Audible pitch controlPress and hold DELAY START TIME key for 5 seconds.
- Audible signal pitch controlPress and hold DELAY START TIME pad for 5 seconds.
- Cooktop LockoutPress and hold the TOP/TOP LIGHT keypad on the control panel for 5 seconds
- Cooktop Lockout FeaturePress and hold TOP/TOP LIGHT keypad on control panel for 5 seconds
- Diagnostics / Test Mode["Plug in microwave oven or reconnect power.","Press Cancel button to reach standby display (colon…
- Diagnostics Mode["Plug in microwave oven or reconnect power.","Press CANCEL button to standby (display shows…
- Disable/Enable All Tones (except end-of-timer and error tones)Press and hold COOK TIME key for 5 seconds.
- Disable/Enable all tones except end-of-timer and error tonesPress and hold COOK TIME pad for 5 seconds.
- Disable/Enable cycle and timer-end repeating tonesPress and hold TIMER SET pad for 5 seconds.
- Fahrenheit to Celsius conversionPress and hold BROIL pad for 5 seconds.
- Forced Defrost Mode (Service Test 38)1. Enter Service Diagnostics Mode. 2. Navigate to Step 38. 3. Select SW3 to toggle
- Fuel type verificationPress and hold START/ENTER key for 5 seconds until fuel type is displayed
- Oven Temperature Calibration AdjustmentPress and hold BAKE pad for 5 seconds. Current offset is shown in 3-digit display; 'CAL' is shown…
- Recall last failure codePress and hold CANCEL/OFF pad for 5 seconds until last error code is displayed.
- Sales Demonstration ModePress and hold TIMER OFF key for 5 seconds.
- Service Diagnostics Mode1
- Software revision numberPress and hold START/ENTER pad for 5 seconds
- Temperature calibration offsetPress and hold BAKE pad for 5 seconds
- Verify fuel typePress and hold START/ENTER key for 5 seconds until fuel type is displayed
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana furnace models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass