Model reference
Amana ML-1/P72909-1M
Microwave
12 documents47 error codes21 service modes
Available documentation
Tech Sheet
- Tech Sheet4 pg
- FICHE TECHNIQUE - W10185206 - Rev B (FR)16 pg
- tech sheet w11415591 revb2 pg
- Tech Sheet - W10005740 - Rev A16 pg
- Failure Code Indications Tech Sheet4 pg
- Technical Service Sheet W10071760 Rev B16 pg
- tech sheet w11332389 revb2 pg
- FICHE TECHNIQUE - 8304417 - Rev B16 pg
Service Manual
- TECHNICAL MANUAL JennAir® and KitchenAid® Under-Counter Microwave Oven with Drawer55 pg
- TECHNICAL MANUAL Low Profile Microwave Hood Combination37 pg
Other
- tech-sheet-w11279384-revA_W1127938416 pg
Installation Guide
- Instrucciones de instalacion38 pg
MyPros+ Max
Diagnose your Amana ML-1/P72909-1M.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (47)
CodeMeaning
:Flashing colon indicates a power failure has occurred.ERRORHumidity sensor (AH sensor) cannot balance the bridge circuit due to…F/01EEPROM communication error between the Central Control Unit (CCU) and the…F/02Pump drive errorF/03Main relays errorF/06Motor Control Unit (MCU) internal failure due to repeating under/over voltage…F/07Main relays errorF/09Motor Control Unit (MCU) has internal failure; repeating under or over voltage…F/10No water detected entering machine or pressure switch trip not detected after 6…F/11Serial communication error between the Central Control Unit (CCU) and the Motor…F/20No water detected entering machine or pressure switch trip not detected after 6…F/21Long drainF/22Door lock errorF/23Heater failureF/24Water temperature sensor (NTC) errorF/25Drive motor tachometer errorF/26Door switch errorF/27Overflow conditionF/28Serial communication errorF/29Door unlock errorF/30Dispenser system errorF/31MCU failureF/32Pump drive system errorF/33Pump drive errorF/34Load detected inside drum during cleaning washer cycle (detected by weight).F/35Main relays errorF/36Motor Control Unit errorF1E4MW Relay failureF2 E0Keypad (keyboard) faultF2 E1Keypad (keyboard) faultView all 47 error codes
F2E1Touch panel failure.F3 E2Warming drawer sensor shorted or open circuit.F4 E1Microwave oven convection thermistor fault.F4 E2Microwave oven internal temperature sensor fault.F4 E4Microwave oven humidity sensor fault.F4E3Exhaust air temperature detection failure.F4E4Humidity sensor error.F5No feature identified for microwaveF5 E0Door and latch switch do not agreeF5 E1Door latch not operatingF6 E5No cavity size commandF8E5Exhaust air temperature detection failure.F9E3Cavity light / cooling fan relay failure (relay K4 does not contact)FDE2Turntable relay failure (relay K6 does not contact)FDE3Exhaust fan relay failure (relay K4 or K5 does not contact)rLLoad detected inside drum during cleaning washer cycle (alternate display for…SdSuds lock
Service modes (21)
- AH Sensor Diagnostic Test (Water Load Cooking Test)["Ensure oven has been plugged in at least 2 minutes before testing.","Fill approximately 200 ml…
- Cavity size programming["Disconnect oven or interrupt power","Wait 10 seconds, reconnect power","Enter diagnostic mode
- Clear last fault code["Disconnect oven or interrupt power","Wait 10 seconds, reconnect power","Enter diagnostic mode
- diagnostic["Plug in microwave oven or reconnect power.","In idle mode, close the door, turn off hood light…
- Diagnostic / Self-Diagnostic Test Mode["Plug in microwave oven or reconnect power.","In idle mode, close the door, turn off hood light…
- Diagnostic / Test Mode["Plug in microwave oven or reconnect power.","In idle mode, close the door, turn off hood light…
- Diagnostic component activation["Enter diagnostic mode (OFF, OFF, START)","Press Bake to activate bake relay","Press Broil once…
- Diagnostic mode["Press OFF","Press OFF","Press START","If the appliance does not enter diagnostic mode, repeat the…
- Fahrenheit/Celsius selection["Press OPTIONS then 1"]
- Manual Diagnostic Test["Washer must be empty and control must be in OFF state.","Close the door.","Select any one key…
- Quick Entry Diagnostic Test (Bypass Service History)1
- Quick Entry Diagnostic Test (bypassing Service History Mode)["Ensure washer drum is empty.","Close the door.","Press POWER.","Select the CLEAN WASHER…
- Quick Entry Diagnostic Test (bypassing Service History)["Drum must be empty.","Close the door.","Push POWER.","Select the CLEAN WASHER cycle.","Press…
- Self-Diagnostic Test Mode["Plug in microwave oven or reconnect power.","In idle mode, close the door, turn off hood light…
- Service History Mode & Diagnostic Test["Washer must be empty and control must be in OFF state.","Close the door.","Select any one key…
- Service History Mode & Diagnostic Test (Universal Entry)["Ensure washer is empty and control is in the OFF state.","Close the door.","Select any one key…
- Temperature calibration adjustment["Press OPTIONS then 6","For double oven only, select desired oven (upper or lower)","Press 3 to…
- Touch Panel and ACU Test (Diagnostic/Test Mode)["Plug in microwave oven or reconnect power.","In idle mode, close the door, turn off hood light…
- Touch Panel and ACU Test (Diagnostics mode)["Plug in microwave oven or reconnect power.","In idle mode, close the door, turn off hood light…
- Touch Panel and ACU Test (Self-Diagnostic Routine)["Plug in microwave oven or reconnect power, in idle mode.","Close the door.","Turn off hood light…
- Touch Panel and ACU Test (Self-Diagnostic)["Plug in microwave oven or reconnect power, unit must be in idle mode.","Close the door.","Turn…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana microwave models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass