mypros+
Model reference

Amana RC-14/P72100-3M

Microwave

1 document62 error codes30 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11467195 - Rev B24 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RC-14/P72100-3M.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (62)

CodeMeaning
afLow inlet air flow condition detected at installation.f:01Primary control failure.f:02Stuck button or user interface mismatch (appears ONLY in Diagnostic Test Mode).f:20No voltage detected at the heater relay (appears ONLY in Diagnostic Test Mode).f:22Outlet thermistor is open.f:23Outlet thermistor has shorted.f:24Inlet thermistor is open (appears ONLY in Diagnostic Test Mode).f:25Inlet thermistor is shorted (appears ONLY in Diagnostic Test Mode).f:26Motor drive system failure.f:28Moisture sensor strip is open (appears ONLY in Diagnostic Test Mode).f:29Moisture sensor strip has shorted (appears ONLY in Diagnostic Test Mode).f:30Restricted air flow condition exists (appears ONLY in Diagnostic Test Mode).f:31L2 line voltage errorf:50No voltage detected at the water valve relay (appears ONLY in Diagnostic Test…f:70No communication between machine control and console electronics.f:71No communication between machine control and console electronics.f:72Console electronics failure (F:72 through F:78).f:73Console electronics failure (F:72 through F:78).f:74Console electronics failure (F:72 through F:78).f:75Console electronics failure (F:72 through F:78).f:76Console electronics failure (F:72 through F:78).f:77Console electronics failure (F:72 through F:78).f:78Console electronics failure (F:72 through F:78).F1 E1ACU (Appliance Control Unit) fault detected.F1 E4UIC (User Interface Control) fault detected.F1 E6Voltage input fault detected.F1 E7Voltage input fault detected.F1E1Primary control failure.F2 E1Dryer keypad stuck errorF2E1Stuck button or user interface mismatch (keypad/user interface failure)
View all 62 error codes
F2E2UI software error; UI cannot read EEPROM software.F3 E1Thermistor faultF3E1Exhaust thermistor is open.F3E2Exhaust thermistor has shorted.F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms)F3E4Inlet thermistor is shorted; temperature above 760°F (<20 ohms)F3E5Both inlet and exhaust thermistors are open; will occur if P14 connector is not…F3E6Moisture sensor strip is openF3E7Moisture sensor strip has shortedF4E1No voltage detected at the heater relayF4E3Restricted air flow detected that may affect dryer performance.F4E4Low L2 voltage (less than 30V) detected at the CCU.F5 E1Dryer door circuit error.F6 E1Communication failure between ACU and UICF6E1Communication error from UI to CCU; communication has not been detected.F6E2Communication error from CCU to UI; communication has not been detected.F7 E6Dryer motor circuit error.F7 E8Dryer motor sense error.F8E1No voltage detected at the water valve relay (steam models only)FC E1Model/Serial number not programmed.FC E2Model/Serial number not matching between ACU and UIC.FC E3Wi-Fi connection fault.FC E4USB stick failure (USB full, not detected, or not accessible).FC E5Software update failureFC E6Model setup export failureFC E7Model setup import failureFC E8Wi-Fi module not responding or not connected.FP E1Coin 1 circuit error.FP E2Coin 2 circuit error.FP E3Card reader communication error.l2Low line voltage (less than 30V) detected at installation.pfPower failure occurred while the dryer was running.

Service modes (30)

  • Component ActivationFrom Service Diagnostics Diagnostics Home screen, select 'Component Activation'
  • Customer-Focused Drying Mode Adjustment["Ensure dryer is in standby mode.","Press and hold the TEMP button for more than 6…
  • Customer-Focused Drying Mode Adjustment (CF1/CF2/CF3)1
  • Customer-Focused Drying Modes Adjustment["Activate the Diagnostic Test Mode.","Select the Component Activation option.","Select…
  • Diagnostic Mode["Enter Setup Mode first.","Press DELICATES keypad for one second while in any of the set-up codes…
  • Diagnostic Test Mode["Ensure the dryer is not currently running a cycle (in-progress screen should not be…
  • diagnostic_modePress DELICATES keypad for one second while in any of the set-up codes 1 through 6 (or while dAS…
  • Displaying Inlet Air Flow Diagnostic (Amana Electric Models Only)["Enter the Diagnostic Test Mode.","Wait for the 5 second delay and cycle through any saved fault…
  • Displaying Line Voltage Diagnostic["Enter the Diagnostic Test Mode.","Wait for the 5 second delay and cycle through any saved fault…
  • Help Mode["Enter Setup Mode first.","Press HEAVY DUTY keypad while in special pricing option step 2.XX (or…
  • help_modePress HEAVY DUTY keypad while in special pricing option step 2.XX (or while dAS displays if…
  • Inlet Air Flow Diagnostic (Amana Electric Models Only)After entering the Diagnostic Test Mode and cycling through saved fault codes, press the Wrinkle…
  • Inlet Air Flow Test (Electric Models Only)["Enter the Diagnostic Test Mode.","Select the Component Activation option.","Press the 'Air Flow'…
  • Line Voltage DiagnosticAfter entering the Diagnostic Test Mode and cycling through saved fault codes, press the Cycle…
  • Line Voltage Test["Enter the Diagnostic Test Mode.","Select the Component Activation option.","Press the 'Line…
  • Manual Diagnostic Test Mode["Perform steps 1 and 2 of Activating the Diagnostic Test Mode.","Select the Component Activation…
  • Manual Diagnostic Test Mode (Component Activation)["Perform steps 1 and 2 of Activating the Diagnostic Test Mode.","Select the Component Activation…
  • Manual Load Test["Enter the Diagnostic Test Mode.","Select the Component Activation option.","Select individual…
  • model_serial_number_menuEnter Help Mode first
  • Model/Serial Number Menu["Enter Help Mode first.","While on the S0 screen press the HEAVY DUTY keypad.","Use NORMAL keypad…
  • Quick Diagnostic TestFrom Service Diagnostics, navigate to Error Diagnostic, then select 'Quick Diagnostic Test'
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only DONE or…
  • Service Diagnostics1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Setup Mode["COIN Models
  • setup_modeCOIN Models
  • UI Component TestFrom Service Diagnostics, navigate to Component Activation, then select 'UI Component Test'
  • USB Menu["Enter Help Mode first.","While on the USB screen press the HEAVY DUTY keypad.","Use NORMAL keypad…
  • usb_menuEnter Help Mode first
  • User Interface/Control System Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
  • wifi_menuWhile in setup mode on the F0 screen, press the HEAVY DUTY keypad to enter Wi-Fi mode.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass