mypros+
Model reference

Amana RC-7PB/P71300-1M

Microwave

7 documents81 error codes34 service modes

Available documentation

Tech Sheet

  • Tech Sheet20 pg
    Covers this model
  • Tech Sheet - W10340328 - Rev A64 pg
    Covers this model
  • Tech Sheet - W11467195 - Rev B24 pg
    Covers this model
  • Tech Sheet 8543719 110 2506650016 pg
    Covers this model

Service Manual

  • Instruction Sheet - 854371916 pg
    Covers this model

Installation Guide

  • Installation Instructions35 pg
    Covers this model
  • Installation Instructions7 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RC-7PB/P71300-1M.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (81)

CodeMeaning
afLow inlet air flow condition detected at installation.CAAverage current limit trip; a 2-second average current draw greater than 5.55…CECommunications error; breakdown in communication between the machine controller…CIInstantaneous current limit trip; a spike of 26 Amps was detected instantly at…E0No errors, functioning ice maker.E1No CoolingE2Motor Lost PositionE3Heater Time-outE4Dry CycleE5IM Bad ThermistorErProcessor reset error; the control failed to save cycle information during a…f:01Primary control failure.f:02Stuck button or user interface mismatch (appears ONLY in Diagnostic Test Mode).f:20No voltage detected at the heater relay (appears ONLY in Diagnostic Test Mode).f:22Outlet thermistor is open.f:23Outlet thermistor has shorted.f:24Inlet thermistor is open (appears ONLY in Diagnostic Test Mode).f:25Inlet thermistor is shorted (appears ONLY in Diagnostic Test Mode).f:26Motor drive system failure.f:28Moisture sensor strip is open (appears ONLY in Diagnostic Test Mode).f:29Moisture sensor strip has shorted (appears ONLY in Diagnostic Test Mode).f:30Restricted air flow condition exists (appears ONLY in Diagnostic Test Mode).f:31L2 line voltage errorf:50No voltage detected at the water valve relay (appears ONLY in Diagnostic Test…f:70No communication between machine control and console electronics.f:71No communication between machine control and console electronics.f:72Console electronics failure (F:72 through F:78).f:73Console electronics failure (F:72 through F:78).f:74Console electronics failure (F:72 through F:78).f:75Console electronics failure (F:72 through F:78).
View all 81 error codes
f:76Console electronics failure (F:72 through F:78).f:77Console electronics failure (F:72 through F:78).f:78Console electronics failure (F:72 through F:78).F0 E7Low Voltage Errorf1 e1Primary control failure.F1 E4HMI (Human Machine Interface) fault detected.F1 E6Voltage input fault detected by the control.F1 E7Voltage input fault detected.F1E1Primary control failure.F1E4Microwave ACU PCBA failure.f2 e1Stuck button or user interface mismatch (keypad/user interface failure)F2 E2Upper Dryer Keypad Stuck ErrorF2E1Stuck button or user interface mismatch (keypad/user interface failure)f3 e1Exhaust thermistor is open.f3 e2Exhaust thermistor has shorted.f3 e6Moisture sensor strip is openf3 e7Moisture sensor strip has shortedF3E1Exhaust thermistor is open.F3E2Exhaust thermistor has shorted.F3E6Moisture sensor strip is openF3E7Moisture sensor strip has shortedF4E4Humidity sensor error.F5 E1Dryer door circuit error detected.F5 E6Upper Dryer Door Circuit ErrorF6 E1ACU to HMI communication faultF7 E6Dryer motor circuit error detected.F7 E7Upper Dryer Motor Circuit ErrorF7 E8Dryer motor sense errorF7 E9Upper Dryer Motor Sense Errorf8 e1No voltage detected at the water valve relay (steam models only)F8E1No voltage detected at the water valve relay (steam models only)F8E5Exhaust air temperature detection failure.FC E1Model/Serial number not programmed into control.FC E2Model and serial numbers stored in ACU and UI do not match.FC E3Wi-Fi connection fault.FC E4USB stick failure (USB full, not detected, or not accessible).FC E5Software update failureFC E6Model setup export failureFC E7Model setup import failureFC E8Wi-Fi module not responding or not connected.FP E1Coin 1 circuit errorFP E2Coin 2 circuit errorFP E3Card reader communication error.l2Low line voltage (less than 30V) detected at installation.LdLong drain; it takes longer than 5 minutes to pump out water to the point where…LFLong fill; the water fill time exceeded 10 minutes, causing the water valves to…LSLid switch error; the control cannot detect lid switch opening/closing…obOff balance; the motor controller detected an unrecoverable off-balance…pfPower failure occurred while the dryer was running.SLSuds lock; excessive suds detected and the unit was unable to clean out suds…SrStuck relay; the relay has failed in the closed position so the machine…

Service modes (34)

  • Automatic Service DiagnosticsControl must be in Off state. Perform Key Dance within 5 seconds
  • Console Keypad and LED TestControl must be in Off state. Perform Key Dance within 5 seconds
  • Customer-Focused Drying Mode Adjustment["Ensure dryer is in standby mode.","Press and hold the TEMP button for more than 6…
  • Customer-Focused Drying Mode Adjustment (CF1/CF2/CF3)1
  • Customer-Focused Drying Modes Adjustment["Activate the Diagnostic Test Mode.","Select the Component Activation option.","Select…
  • Diagnostic / Test Mode["Plug in microwave oven or reconnect power.","Press CANCEL to enter Standby mode (colon ':'…
  • Diagnostic Mode (Field Diagnostic Cycle)["Enter Setup Mode first.","Navigate to set-up code 6 or 7 (or while dAS displays if operating with…
  • Diagnostic Test Mode["Ensure the dryer is not currently running a cycle (in-progress screen should not be…
  • diagnostic_mode["Enter setup mode (see setup mode entry).","Navigate to any of the set-up codes 1 through 6 (or…
  • Displaying Inlet Air Flow Diagnostic (Amana Electric Models Only)["Enter the Diagnostic Test Mode.","Wait for the 5 second delay and cycle through any saved fault…
  • Displaying Line Voltage Diagnostic["Enter the Diagnostic Test Mode.","Wait for the 5 second delay and cycle through any saved fault…
  • Help Mode["Enter Setup Mode first.","Navigate to set-up option 2.XX (or while dAS displays if operating with…
  • help_mode["Enter setup mode.","Navigate to special pricing option step 2.XX (or while dAS displays if…
  • Inlet Air Flow Diagnostic (Amana Electric Models Only)After entering the Diagnostic Test Mode and cycling through saved fault codes, press the Wrinkle…
  • Inlet Air Flow Test (Electric Models Only)["Enter the Diagnostic Test Mode.","Select the Component Activation option.","Press the 'Air Flow'…
  • Line Voltage DiagnosticAfter entering the Diagnostic Test Mode and cycling through saved fault codes, press the Cycle…
  • Line Voltage Test["Enter the Diagnostic Test Mode.","Select the Component Activation option.","Press the 'Line…
  • Manual Diagnostic Test Mode["Perform steps 1 and 2 of Activating the Diagnostic Test Mode.","Select the Component Activation…
  • Manual Diagnostic Test Mode (Component Activation)["Perform steps 1 and 2 of Activating the Diagnostic Test Mode.","Select the Component Activation…
  • Manual DiagnosticsControl must be in Off state. Perform Key Dance within 5 seconds
  • Manual Load Test["Enter the Diagnostic Test Mode.","Select the Component Activation option.","Select individual…
  • model_serial_number_menu["Enter Help Mode.","While on the S0 screen, press the HEAVY DUTY keypad.","Use NORMAL keypad to…
  • Model/Serial Number Menu["Enter Help Mode.","While on the S0 screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • Nutate and Recirculate TestControl must be in Off state. Perform Key Dance within 5 seconds
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only DONE or…
  • Service Diagnostics ModePress SW1 and SW2 simultaneously for 3 seconds
  • Setup Mode (Control Set-Up)["PD Models
  • setup_mode["PD Models
  • Spin and Drain TestControl must be in Off state. Water should be present in the unit. Perform Key Dance within 5…
  • USB Menu["Enter Help Mode.","While on the USB screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • usb_menu["Enter Help Mode.","While on the USB screen, press the HEAVY DUTY keypad.","Use NORMAL keypad to…
  • User Interface/Control System Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
  • Water Inlet and Dispenser Valve Operating PS TestControl must be in Off state. Perform Key Dance within 5 seconds
  • wifi_menuWhile in setup mode on the F0 screen, press the HEAVY DUTY keypad to enter Wi-Fi mode.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass