mypros+
Model reference

Amana RC10B-PB/P74582-2M

Microwave

2 documents46 error codes15 service modes

Available documentation

Tech Tip

  • Instruction Sheet - 3978720 - Rev A12 pg
    Covers this model
  • Instruction Sheet2 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RC10B-PB/P74582-2M.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (46)

CodeMeaning
AFLow inlet air flow detected at install.d13Coin 2 errord16Generation 2 debit card reader errord5Coin 1 errord9Low voltage detection errorF:01Primary control failure.F:02Stuck button or user interface mismatch (appears ONLY in Diagnostic Test Mode).F:20No voltage detected at the heater relay (appears ONLY in Diagnostic Test Mode).F:22Outlet thermistor is open.F:23Outlet thermistor has shorted.F:24Inlet thermistor is open (appears ONLY in Diagnostic Test Mode).F:25Inlet thermistor is shorted (appears ONLY in Diagnostic Test Mode).F:26Motor drive system failure.F:28Moisture sensor strip is open (appears ONLY in Diagnostic Test Mode).F:29Moisture sensor strip has shorted (appears ONLY in Diagnostic Test Mode).F:30Restricted air flow condition exists (appears ONLY in Diagnostic Test Mode).F:31Low voltage condition (less than 30 V) detected (appears ONLY in Diagnostic…F:50No voltage detected at the water valve relay (appears ONLY in Diagnostic Test…F:70No communication between the machine control and the console electronics.F:71No communication between the machine control and the console electronics.F:72Console electronics failure (F:72 through F:78).F:73Console electronics failure (F:72 through F:78).F:74Console electronics failure (F:72 through F:78).F:75Console electronics failure (F:72 through F:78).F:76Console electronics failure (F:72 through F:78).F:77Console electronics failure (F:72 through F:78).F:78Console electronics failure (F:72 through F:78).F01CCU errorF11MCU errorF20No water detected entering washer
View all 46 error codes
F21Long drainF22Door lock errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between CCU and MCU.F29Door unlock errorF30Dispenser system errorF31Overheating of motorF34Load detected in washer during Washer Cleanout Cycle.F70Communication failure between CCU and UI (User Interface).F73UI failureF74UI failureL2Low line voltage (less than 30 V) detected at installation.PFPower failure occurred while the dryer was running.

Service modes (15)

  • Code Display Mode["Can only be accessed when the washer is in error state.","PD Models
  • Customer-Focused Drying Mode Adjustment["In Standby mode (dryer plugged in but not powered up), press and hold the Dryness Level button…
  • diagnostic["Set Fabric Care / Temperature switch to AIR FLUFF / NO HEAT","Set Signal switch to LOUDER","Set…
  • diagnostic_test["Ensure door is open.","Set Fabric Care / Temperature switch to AIR FLUFF / NO HEAT.","Set Signal…
  • Help Mode (dAS Mode)["Open the service door or insert a manual diagnostic card.","The message dAS will appear in the…
  • Help Mode (PD Models)["Open the service door.","Press the WOOLENS key until the display reads 2.XX.","Press the…
  • less_dry_test["Begin with a fully assembled, empty dryer with clean lint screen connected to known good power…
  • Manual Load Test["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
  • Manual Overview Test["Enter Flashing Mode (entire display flashing).","Press the WHITES key pad to start Manual…
  • Quick Overview Test["Enter Flashing Mode (entire display flashing).","Press the WOOLENS key pad to start Quick…
  • Service Access Code["Only functions on washers set up for 0 vend price without any Special Pricing set-up, and the…
  • Service Diagnostic Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Done…
  • Setup Mode (PD Models)["Insert access door key, turn, and lift to remove access door.","Use lower fabric setting key pads…
  • Setup Mode (PN Models)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
  • Washer Diagnostic Mode (Flashing Mode)["First enter 'Start Operating Set-Up' mode.","Then press and hold the DELICATES & KNITS key pad…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass