mypros+
Model reference

Amana RR-7D/P73307-1M

Microwave

9 documents51 error codes21 service modes

Available documentation

Tech Sheet

  • Tech Sheet W11398327 RevA4 pg
    Covers this model
  • Tech Sheet W11365092 RevA4 pg
    Covers this model
  • FICHE TECHNIQUE - 8304553 - Rev B16 pg
    Covers this model
  • Tech Sheet - W112248132 pg
    Covers this model
  • Tech Sheet - W10403269 - Rev A52 pg
    Covers this model

Service Manual

  • ADC AD-200 ServiceManual-NonTilt-1993-thru-1998 PastProduction OPL82 pg
    Covers this model
  • Job Aid - 4322536A (G-20)76 pg
    Covers this model
  • Job Aid - Whirlpool Microwave Oven Hood Combination54 pg
    Covers this model

Installation Guide

  • Installation Instructions35 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RR-7D/P73307-1M.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (51)

CodeMeaning
AFRestricted airflow detected that may affect dryer performance.doorDoor switch circuit is opendSFLFault detected in the microprocessor temperature sensing circuitEnter clockPower failure has occurred; 'Enter clock' flashes on display.F0E0No error(s) foundF1E0Internal failureF1E1Oven appliance manager failure (not applicable for lower oven on double oven…F1E3Incorrect controller installed (electric models only); ACU and/or UI part…F1E4MW Relay failure (Relay 4903 on ACU).F2Touch panel failure.F2E0Keypad disconnected.F2E1Stuck key or shorted key.F2E2LED error on user interface.F2E3User Interface Software Error 2F2E4UI Software ErrorF2E5UI Software ErrorF3E0Upper oven temperature sensor open or shorted.F3E1Lower oven temperature sensor open or shorted.F3E2Warming drawer sensor shorted (oven not equipped with this feature).F3E3Meat probe sensor shorted.F3E4Inlet thermistor is shorted; temperature above 391°F (<20 ohms).F3E5Inlet and exhaust thermistors are open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; only appears in service diagnostic mode.F3E7Moisture sensor strip has shorted; only appears in service diagnostic mode.F3HHumidity sensor failure.F4E1No voltage detected at the heater relay; only appears in service diagnostic…F4E2Heater 2 failure or connector problem (electric models only); no voltage…F4E3Restricted/low air flow that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at installation.F5E0Door switch and latch switch do not agree.
View all 51 error codes
F5E1Door latch not operating.F6Microwave relay failure.F6E0Lost communication (for microwave ovens only).F6E1Cook oven over temperature.F6E2Clean oven over temperature.F6E3Mini oven/warm drawer over temperature (not for built-in ovens).F6E4User interface/appliance manager mismatch.F6E5Cavity size is incorrect.F7E0Water level is not high enough or water did not boil fast enough.F7E4Conductivity sensor not connected.F8E0Low fan speed underspeedF8E1Low fan speed overspeedF8E2High fan speed underspeedF8E3High fan speed overspeedF8E5Exhaust air temperature detection failure.FILLNormal idle/ready state display indicating the dryer is ready to accept a cycle…HotPossible overheating conditionL2Low L2 voltage (less than 50V) detected at installation.MV-4903MW Relay failure (relay contact on ACU has welded closed).PFPower failure occurred while the dryer was running.SEFLRotational sensor circuit failure

Service modes (21)

  • Adjusting Customer-Focused Dryness LevelIn standby mode (dryer plugged in but not powered up), press and hold the DRYNESS button for…
  • Customer-Focused Dryness Level Adjustment1
  • diagnosticPress any one of the 3 keys 3 times within 8 seconds.
  • Diagnostic / Self-Diagnostic Test Mode["Plug in microwave oven or reconnect power.","In idle mode, close the door, turn off hood light…
  • Diagnostic / Test Mode["Plug in microwave oven or reconnect power.","In idle mode, close the door, turn off hood light…
  • Diagnostic modePress OFF, OFF, START to enter diagnostic mode and check fault codes.
  • Diagnostics ModePress any 3 keys 3 times within 8 seconds
  • Diagnostics mode (for failure code verification)["Press CANCEL
  • Extended diagnostic mode (relay activation and testing)1
  • Install Diagnostics1
  • Key Activation & Encoder TestFrom Service Diagnostic Mode, press and release the 1st button used to activate Service Diagnostic…
  • Quick Diagnostic TestFrom Service Diagnostics, navigate to Error Diagnostic > Quick Diagnostic Test
  • Service Diagnostic Mode1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Service Diagnostics1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Service Test ModeFrom Service Diagnostic Mode, press and release the 2nd button used to activate Service Diagnostic…
  • Software Version Display1
  • Touch Panel and ACU Diagnostic Test["Plug in microwave oven or reconnect power.","In idle mode, close the door, turn off hood light…
  • Touch Panel and Electronic Control Self-Diagnostic Test Mode["Press and hold the OFF/CANCEL button while opening the door.","While still holding the OFF/CANCEL…
  • UI Component TestFrom Service Diagnostics, navigate to Component Activation > UI Component Test
  • User interface programming (after UI replacement)1
  • User Interface/Control System Test1. Activate Service Diagnostic Mode. 2. Press and release the 1st button used to activate Service…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass