mypros+
Model reference

Amana RS-7A/P75589-5M

Microwave

8 documents45 error codes27 service modes

Available documentation

Tech Sheet

  • Wiring Diagram - W10113803 - Rev A32 pg
    Covers this model
  • Tech Sheet12 pg
    Covers this model
  • Tech Sheet - W11045355 - Rev B12 pg
    Covers this model
  • techsheet-w10420006-reva_W1042000656 pg
    Covers this model
  • Tech Sheet - W10393006 - Rev B52 pg
    Covers this model
  • Service Guide - Tech Sheet W1117522244 pg
    Covers this model

Other

  • tech manual w11467698 reva29 pg
    Covers this model
  • tech-sheet-W10865055-RevA60 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RS-7A/P75589-5M.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (45)

CodeMeaning
AFRestricted/low air flow detected that may affect dryer performance.F0 E7Control board recognized line voltage below 90 VAC.F1 E1ACU (Appliance Control Unit) fault.F1 E7ACU voltage input fault.F1E1Indicates a Cycle Control Unit (CCU) problem.F1E3Incorrect controller installed (electric models only); ACU and/or UI part…F1E4Microwave ACU PCBA failure.F1E5ACU parameter file missing; parameter memory invalid.F2 E1Lower dryer keypad is sensed pressed for 60 seconds (stuck key).F2 E2Upper dryer keypad is sensed pressed for 60 seconds (stuck key).F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; only…F2E2User Interface Software ErrorF2E4UI software errorF2E5UI software errorF3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms)F3E4Inlet thermistor is shorted; temperature above 760°F (<20 ohms)F3E5Inlet and exhaust thermistors are both open; will occur if P14 connector is not…F3E6Moisture sensor strip is openF3E7Moisture sensor strip has shortedF4E1No voltage detected at the heater relayF4E2Heater 2 failure or connector problem (electric models only); no voltage…F4E3Restricted air flow detected that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.F4E9ACCUPOP error.F5 E1Lower dryer door circuit error.F5 E6Upper dryer door circuit error.F6E1Communication between the CCU and UI has not been detected (UI to CCU).F6E2Communication between the CCU and UI has not been detected (CCU to UI).
View all 45 error codes
F6E3Communication errorF7 E6Lower dryer motor circuit error.F7 E7Upper dryer motor circuit error.F7 E8Lower dryer motor sense errorF7 E9Upper dryer motor sense errorF8E5Exhaust air temperature detection failure.FC E1Model/Serial number not programmed into control.FC E4USB stick failure (USB full, not detected, or not accessible).FC E5Software uploaded from USB stick does not match the model number of the machine.FCE1WIFI Module has not responded for a specified amount of time; communications…FP E1Coin 1 circuit errorFP E2Coin 2 circuit errorFP E3Card reader communication error.L2Low L2 voltage (less than 50V) detected at the CCU.PFPower failure occurred while the dryer was running.

Service modes (27)

  • Component ActivationFrom Service Diagnostics Diagnostics Home screen, select 'Component Activation'
  • Customer-Focused Dryness Level Adjustment1. Turn cycle selector knob to an automatic cycle. 2. From the Automatic Cycle Main Screen, press…
  • Diagnostic Cycle (Factory)["Enter Service Mode.","Navigate to Factory Diagnostics.","Select Diagnostic Cycle.","Press the…
  • Diagnostic Cycle (Service)["Enter Service Mode.","Navigate to Service Diagnostics.","Select Diagnostic Cycle.","Press the…
  • Diagnostic Mode["Enter Setup Mode first.","While in any of the set-up codes 1 through 6 (or while dAS displays if…
  • Diagnostic Test Mode["Plug in microwave oven or reconnect power.","Press Cancel button to enter standby (colon ':'…
  • Diagnostics / Test Mode["Plug in microwave oven or reconnect power.","Press CANCEL keypad to go to Standby mode (display…
  • Fault Code Display and Clear["Activate Service Diagnostic Mode first.","Press and release the 3rd button to display the most…
  • Fault/Error Code Display["From the DIAGNOSTICS HOME screen, press ERROR DIAGNOSTIC button.","If there are no saved fault…
  • Fault/Error Code Display and Clear1. Activate Service Diagnostic Mode. 2. Press and release the 3rd button to display next error…
  • Help Mode["Enter Setup Mode first.","While in special pricing option step 2.XX (or while dAS displays if…
  • Install Diagnostics["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
  • Key Activation & Encoder Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • Loads Test Mode["Ensure the dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds…
  • Model/Serial Number Menu["Enter Help Mode.","While on the S0 screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • Quick Diagnostic TestFrom Diagnostics Home screen, select 'Error Diagnostic', then select 'Quick Diagnostic Test'
  • Reset Modifiers and Options to Factory Default1
  • Service Diagnostic Mode["Ensure the dryer is in standby mode (plugged in with all indicators off).","Select any three (3)…
  • Service Diagnostics1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Service Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three (3)…
  • Service Test Mode["Activate Service Diagnostic Mode first.","From the Diagnostics Home screen, scroll down and…
  • Setup Mode["Stacked PD Models
  • Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
  • UI Component TestFrom Diagnostics Home screen, select 'Component Activation', then select 'UI Component Test'
  • USB Menu["Enter Help Mode.","While on the USB screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • User Interface Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
  • User Interface/Control System Test1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass