mypros+
Model reference

Amana RV-10A

Microwave

2 documents57 error codes15 service modes

Available documentation

Tech Sheet

  • Tech sheet60 pg
    Covers this model
  • tech sheet w11417645 revb56 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RV-10A.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (57)

CodeMeaning
AFLow airflow detected that may affect dryer performance.drnDrain pump system problemF0E1Load detected in drum during Clean Washer cycle.F0E2Excessive suds detected in washer; washer is running a suds reduction routine.F0E3High temperature error during dry cycle, no air flow detected; dryer fan not…F0E4High temperature error during wash cycle; washer water too hot, possibly inlet…F0E5Off balance load detected; load could be unbalanced or too large.F1E1Motor relay stuck on, indicates an ACU problem.F1E2MCU over- or under-voltage error; MCU malfunction with voltage out of range.F1E3Incorrect controller installed (electric models only); ACU or UI part number…F1E4Main relay open or shorted.F1E5ACU parameter file missing; parameter memory invalid.F2E1Stuck button on User Interface (depressed for over 20 seconds); only appears in…F2E3UI mismatchF2E4UI software errorF2E5UI software errorF3E1Pressure switch signal missing or out of range.F3E2Wash NTC (thermistor) open or shorted.F3E3Dry thermistor NTC open or shorted.F3E5Dry NTC fault; dry temperature sensor out of range, open circuit, or short…F3E6Accelerometer error.F3E7Rear moisture sensor strip is open or shorted (Maytag models only); only…F4E1Wash heater relay error.F4E2Dry heater relay error.F4E3Dry fan motor error.F4E4L2 line voltage error (electric models only); low L2 voltage (less than 50V)…F4E5High limitF5E1Door switch error.F5E2Lock failure.F5E3Unlock failure.
View all 57 error codes
F5E4Door not open error.F6E1Communication between the Appliance Control Unit (ACU) and Motor Control Unit…F6E2Communication between the Appliance Control Unit (ACU) and Human Machine…F6E3Unknown cycle ID error.F7E0Loss of powerF7E1Loss of power during spinF7E10Motor disconnected error (also displayed as F7EA).F7E12MC/MCU Overload (also displayed as F7EC).F7E2MCU over temperature error.F7E3MCU over current error or internal failure.F7E4Motor disconnected error.F7E5Shifter failure.F7E6Motor circuit openF7E7Motor unable to meet target RPM.F7E8Motor over temperature error.F7E9Locked rotor.F7EAMotor disconnected error (alternate display of F7E10).F7ECMC/MCU overload (alternate display of F7E12).F8E1Inlet valve error or fill timeout.F8E3Overflow condition detected.F8E6Water hazardF9E1Long drain or drain timeout.F9E2Drain pump system problemL2Low L2 voltage (less than 30V) detected at the CCU.LFLong fillLo FloLong fill (alternate display of F8E1).PFPower failure occurred while the dryer was running.

Service modes (15)

  • Component Activation (within Service Diagnostic Mode)["From the DIAGNOSTICS HOME screen, scroll down and select 'Component Activation'.","Activate…
  • Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS or DRY LEVEL…
  • Fault Code Display / Clearing["Enter Service Diagnostic Mode.","If saved fault code exists, it will be flashing in the display…
  • Fault/Error Code Display["Enter Service Diagnostic Mode; most recent fault code is shown automatically.","Press the 3rd…
  • Human-Machine Interface Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • Key Activation & Encoder Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • Quick Diagnostic Test["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
  • Service Calibration["Enter Service Test Mode.","Select function number 052 using Soil Level/Temp buttons or cycle…
  • Service Diagnostic Mode1. Ensure washer/dryer is in standby mode (plugged in with all indicators off). 2. Open and close…
  • Service Diagnostic Mode (Alternate Method)1
  • Service Diagnostic Mode (Primary Method)["Ensure washer/dryer is in standby mode (plugged in with all indicators off).","Open and close the…
  • Service Diagnostics (Automated Test Cycle)["Enter Service Test Mode.","Select function number 051 using Soil Level/Temp buttons or cycle…
  • Service Test Mode["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
  • Service Test Mode (Load Control)["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
  • Software Version Display["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass