Model reference
Amana XLC20000
Microwave
10 documents85 error codes22 service modes
Available documentation
Tech Sheet
- Tech Sheet48 pg
- Tech Sheet48 pg
- Tech Manual - W11739870 - Rev A36 pg
- Tech Sheet - W10115139A (SP)8 pg
- Tech Sheet - W10118202A (SP)8 pg
- Tech Sheet - W10116547A (SP)12 pg
- Tech Sheet24 pg
Tech Tip
- Instruction Sheet - W11581423 - Rev A - Gas Conversion Kit42 pg
Installation Guide
- Installation Instructions27 pg
- Instrucciones de instalacion27 pg
MyPros+ Max
Diagnose your Amana XLC20000.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (85)
CodeMeaning
:Blinking or flashing colon indicates a power failure has occurred.03/08Door and switches do not agree (door position disagreement).11Oven sensor opened (upper oven bake/broil circuit).12Oven sensor shorted (upper oven bake/broil circuit).1CShorted key detected on keypad.1dBake/Broil range over temperature condition (alternate display code).21Oven sensor opened (lower oven circuit).22Oven sensor shorted (lower oven circuit).2CKeytail unplugged.3 beepsThermistor or wiring harness is either short-circuited or open; dryer shuts off…31Latch error during CLEAN mode.32Latch error during CLEAN mode.3dBake/Broil range over temperature condition.4dInternal control error.51Clean range over temperature condition.52Clean range over temperature condition.6CEEPROM communications error.7CInternal control error.8CInternal control error.9dDoor latch not operating properly.Blocked coin 1Blocked coin 1 or coin drop UI control circuit failure (coin recognition and…Blocked coin 2Blocked coin 2 or coin drop UI control circuit failure (coin recognition and…CCU communication errorCCU is not receiving communications from UI (display disabled while error…CLrNo error(s) foundDebit card reader communication errorNot receiving communications from installed debit card reader in Enhanced…E1Thermistor is open.E2Thermistor is shorted.E3User interface or software mismatch (key switch or software mismatch); only…Err4Ambient temperature sensor out of allowed range (displayed during diagnostic…Exhaust thermistor openExhaust thermistor open, temperature drops below 18°F (>50 kΩ) for 1 minute in…View all 85 error codes
Exhaust thermistor shortedExhaust thermistor shorted, temperature above 250°F (<500Ω) for 1 minute in Run…F-01Main control failure.F-02Keyboard/user interface failureF-22Outlet thermistor open circuit.F-23Outlet thermistor short circuit.F-26Drive motor system failure.F-28Moisture sensor open circuit (only appears in diagnostic test mode).F-29Moisture sensor short circuit (only appears in diagnostic test mode).F0E2Excess suds detectedF0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Unbalanced load detected during cycle.F1Control failureF1E1Main control board failure.F1E2Motor control section failure on the main control board.F1E3-0ACU Relay FailureF1E3-AMWO Cooling Fan FailureF1E4MW Relay ErrorF2Keyboard (membrane switch) failure.F2E1Keypad stick error.F2E3Switch mismatchF3Oven temperature sensor opened or shorted.F3E1Pressure system failureF3E2Inlet water temperature sensor (thermistor) detected open or shorted.F3E3-0Meat Probe FailureF4E1-0Cavity NTC FailureF4E1-1Cavity NTC FailureF4E3Exhaust air temperature sensor error.F4E4Humidity Sensor FailureF4E9MW Relay Synchro ErrorF4EA-0Toast NTC FailureF4EA-1Toast NTC FailureF5Door and door switches do not agree (mismatch between door position and switch…F5E1Lid switch failureF5E2Open Door FailureF5E3Lid unlock failureF5E4Lid not opened between cyclesF5E6Door error.F6Microwave relay failure.F6E1-0ACU/HMI Communication FaultF7E1Basket speed failureF7E5Shifter failureF7E6Motor failureF7E7Motor cannot reach target RPMF7E9Vent error.F8E1No fill or long fillF8E3Overflow condition detected.F9E1Long drainFBE4MWO Cooling fan error.FDE3Exhaust Fan Relay error.Low voltageVoltage detected below 90 VAC for 8 seconds.Motor control circuit errorDryer motor control circuit errorPFPower failure occurred while the dryer was running.UI communication errorUI is not receiving communications from CCU (display disabled while error…UI EEPROM CRC failureUI EEPROM memory is a CRC failure (display disabled until diagnostic code is…UI EEPROM read errorUI Microprocessor is not able to read or verify EEPROM (display disabled until…
Service modes (22)
- Automatic Test Mode (02)["Enter diagnostic test mode (see entry procedure).","Turn cycle selector knob until LED pattern…
- Calibration Mode (04)["Enter diagnostic test mode (see entry procedure).","Turn cycle selector knob until Rinse LED is…
- Console Diagnostics (Switches and Indicators)["Enter Diagnostic Test Mode.","Press each button or rotate the cycle selector to each cycle…
- Diagnostic Test["Ensure dryer is fully assembled and connected to a known power source.","Open the door.","Set…
- Diagnostic Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or only Cycle Complete…
- Diagnostic Test Modes (entry)["RESET
- Diagnostics / Test Mode["Plug in microwave oven or reconnect power.","Press the Cancel keypad to go to standby (display…
- Diagnostics ModeWith oven not in cooking or broiling mode, press Cancel/OFF > Cancel/OFF > START. The control will…
- Door Switch Diagnostic["Enter Diagnostic Test Mode.","Open the door
- Dryness Level Adjustment["Enter Diagnostic Test Mode.","Press and hold the Dryness Level button for 5 seconds
- Dryness Level Adjustment Mode["Activate Diagnostic Test Mode and advance past stored fault codes.","In diagnostic test mode…
- Engineering ModePress UPPER BAKE, enter 100 on the keypad, then press and hold UPPER BAKE for three (3) seconds.
- Fault Code Display Mode (01)["Enter diagnostic test mode (see entry procedure).","Turn cycle selector knob until the Done LED…
- Humidity Sensor Diagnostic["Enter Diagnostic Test Mode.","Locate two metal strips on the front of the lint screen…
- Less Dry Test["Ensure dryer is fully assembled and empty with clean lint filter.","Close the door.","Set timer…
- Manual Test Mode (03)["Enter diagnostic test mode (see entry procedure).","Turn cycle selector knob until LED pattern…
- Self-diagnostic test mode["1
- Service Diagnostic Mode["Press Settings","Press Info","Press Service and Support","Press CONFIRM button two times","Press…
- SW Version Display Mode (07)["Enter diagnostic test mode (see entry procedure).","Turn cycle selector knob until LED pattern…
- Tachometer Check Mode (09)["Enter diagnostic test mode (see entry procedure).","Turn cycle selector knob until Wash and Done…
- Temperature Adjustment ModePress BAKE key for three (3) seconds, then enter 550
- UI Test Mode (06)["Enter diagnostic test mode (see entry procedure).","Turn cycle selector knob until Rinse and Spin…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana microwave models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass