mypros+
Model reference

Amana CC-6/P27271-6S

Range

55 error codes54 service modes
MyPros+ Max

Diagnose your Amana CC-6/P27271-6S.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (55)

CodeMeaning
ACCUDryer motor control circuit errord13Coin 2 errord16Generation 2 debit card reader errord5Coin 1 errord6Coin 2 error (dryer)d9Low voltage detection errorF01CCU errorF03Accelerometer failureF04Accelerometer failureF07Main control cannot determine position of shifter (shifter system failure).F1Blocked coin 1 or coin drop UI control circuit failure (coin recognition and…F1 E1ACU (Appliance Control Unit) fault detected.F1 E4HMI (Human Machine Interface) fault detected.F1 E6Voltage input fault detected by the control.F11MCU errorF2Voltage detected below 90 VAC for 8 seconds.F2 E1Stuck keypad errorF20No water detected entering washerF21Long drainF22Door lock errorF23Dryer exhaust thermistor shorted errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between CCU and MCU.F29Door unlock errorF3Blocked coin 2 or coin drop UI control circuit failure (coin recognition and…F3 E1Thermistor faultF30No description available
View all 55 error codes
F31Overheating of motorF32No fill condition detected; water level does not change.F33Pump disconnectedF34Load detected in washer during Washer Cleanout Cycle.F4Not receiving communications from installed debit card reader in Enhanced…F5Dryer motor control circuit error (cycles and price display disabled until…F5 E1Dryer door circuit error detected.F6 E1ACU to HMI communication faultF7 E6Dryer motor circuit error detected.F7 E8Dryer motor sense errorF70Communication failure between CCU and User Interface Control (UIC).F71Communication failure from UIC to dryer CCUF73UIC failureF74UIC failureF77Off balance load detected.FC E1Model/Serial number not programmed into control.FC E2Model and serial numbers stored in ACU and UI do not match.FC E4USB stick failure (USB full, not detected, or not accessible).FC E5Software update failureFC E6Model setup export failureFC E7Model setup import failureFP E1Coin 1 circuit errorFP E2Coin 2 circuit errorFP E3Card reader communication error.TRACExhaust thermistor open

Service modes (54)

  • Clean Washer Cycle["Enter Diagnostic Mode (display is flashing).","Press BRIGHTS button to start the Clean Washer…
  • Code Display Sub-mode["Open the service door.","The current F or d code is displayed (only accessible when washer is in…
  • Credit a Cycle["Enter Diagnostic Mode (display is flashing).","Press PERM
  • diagnostic["Enter set-up mode first.","Navigate to set-up code 6 (or dAS display if operating with Maytag…
  • Diagnostic Mode["Enter set-up mode","Navigate to set-up code 6 or 7 (or while dAS displays if operating with…
  • Diagnostic Mode (Blink Mode)["First access Setup/Configuration Mode.","Press DELICATES & KNITS button for 1 second while one of…
  • Diagnostic Mode (Washer Diagnostic Mode)["Press 'Start Operating Set-up' button to enter setup mode.","Press and hold DELICATES AND KNITS…
  • diagnostic_mode["Enter setup mode (see setup mode entry).","Navigate to any of the set-up codes 1 through 6 (or…
  • help["Enter set-up mode first.","Navigate to set-up option 2.XX (or dAS display if operating with…
  • Help Mode["PD models
  • Help Mode (dAS mode)1
  • Help Mode (PD models)1
  • help_mode["Enter setup mode.","Navigate to special pricing option step 2.XX (or while dAS displays if…
  • Manual Overview Test["Enter Flashing Mode (diagnostic mode with entire display flashing).","Press the WHITES button."]
  • model_serial_number_menu["Enter Help Mode.","While on the S0 screen, press the HEAVY DUTY keypad.","Use NORMAL keypad to…
  • P-01 Cancel Cycle, Reset Errors, and Clear Escrow["Enter Service Diagnostic Test Mode.","Press START after 'P-01' is displayed."]
  • P-01 Clear Errors["Access Service Diagnostic Test Modes.","Display shows 'P-01'.","Press START to clear active error…
  • P-02 Cycle Credit["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE washer key pad until 'P-02' is…
  • P-03 Quick Overview Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE washer key pad until 'P-03' is…
  • P-03 Service Diagnostic["Access Service Diagnostic Test Modes.","Press NORMAL key pad until 'P-03' is displayed.","Press…
  • P-04 Manual Diagnostic["Access Service Diagnostic Test Modes.","Press NORMAL key pad until 'P-04' is displayed.","Press…
  • P-04 Manual Overview Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE washer key pad until 'P-04' is…
  • P-05 Button Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE washer key pad until 'P-05' is…
  • P-05 Calibration Cycle["Access Service Diagnostic Test Modes.","Press NORMAL key pad until 'P-05' is displayed.","Press…
  • P-06 Drain and Spin["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE washer key pad until 'P-06' is…
  • P-07 UI Diagnostics["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE washer key pad until 'P-07' is…
  • P-08 Clean Washer Cycle["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE washer key pad until 'P-08' is…
  • P-09 Tachometer Verification["Access Service Diagnostic Test Modes.","Press NORMAL key pad until 'P-09' is displayed.","Press…
  • P-10 Dryer Diagnostic Cycle["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE washer key pad until 'P-10' is…
  • P-12 Clean Washer Cycle["Access Service Diagnostic Test Modes.","Press NORMAL key pad until 'P-12' is displayed.","Press…
  • Quick Drain and Spin["Enter Diagnostic Mode (Blink Mode).","Press COLORS button while the display is blinking."]
  • Quick Overview Test["Enter Flashing Mode (diagnostic mode with entire display flashing).","Press the DELICATES AND…
  • Quick Spin Cycle["Enter Diagnostic Mode (display is flashing).","Press COLORS button to start the Quick Spin…
  • Service Access Code (free-vend models only)1. Open the door. 2. Within 10 seconds, press in sequence
  • Service Access Code (PN Models without key switch)["Only functions on washers set up for 0 vend price without any Special Pricing set-up, and…
  • Service Diagnostic Test Mode["Enter Set-Up Mode (insert service switch key and turn counter-clockwise).","Make sure display…
  • Service Diagnostic Test Modes1. Disconnect power and remove service door (PD models) or remove AA1 jumper from IU control board…
  • Service Diagnostic Test Modes (Entry)["1. For coin models
  • Set-up Mode["PD/PN/PR Models
  • setup["PD Models: Insert access door key, turn, and lift to remove access door.","PN/PR Models (Option…
  • Setup Mode (PD Models)["Insert service access door key, turn, and lift to remove access door.","Use DELICATES AND KNITS…
  • Setup Mode (PN Models)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
  • Setup Mode (PR Models set up as PN via Service Access Code)["Press Left Button","Press Right Button","Press Left Button","Press Right Button","Press Right…
  • Setup Mode (PR Models via AA1 connector)["Unplug dryer or disconnect power","Open console, disconnect jumper on AA1","Close console","Plug…
  • Setup Mode (PR Models via Gen. 2 card reader)["Install a Gen
  • setup_mode["PD Models
  • Setup/Configuration Mode["PD models
  • Setup/Configuration Mode (PD models)Insert key into service access door, turn and lift to remove the service access door.
  • Setup/Configuration Mode (PR models)Insert setup card (from card reader manufacturer) into card reader
  • Setup/Programming Mode["For coin-operated models
  • Technician Service Access Code (PR models, free vend only)["Press the POWERWASH, EXTRA RINSE, TEMPERATURE, and DELICATES key pads within 10 seconds."]
  • usb_menu["Enter Help Mode.","While on the USB screen, press the HEAVY DUTY keypad.","Use NORMAL keypad to…
  • Washer Cleaning Program["Enter Diagnostic Mode (Blink Mode).","Press BRIGHT button while the display is blinking."]
  • Washer Diagnostic Mode["First enter 'Start Operating Set-Up' (setup mode).","Press and hold the QUICK CYCLE button for 1…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana range models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass