Model reference
Amana RCC-3-L1
Range
15 documents67 error codes12 service modes
Available documentation
Tech Sheet
- Wiring Diagram - W10703187 - Rev B2 pg
- W10751162A.fm12 pg
- Wiring Diagram - W10750126 - Rev A2 pg
- Wiring Diagram - W10902664 - Rev A2 pg
- TECH SHEET - 9754365 - Rev A8 pg
- Tech Sheet 97543654 pg
- TECH SHEET - KitchenAid Range KESH307HBS68 pg
Service Manual
- Pro Line™ & Commercial Blender Service Manual44 pg
- ADC AD-75THS ServiceManual-PH5 PastProduction OPL73 pg
- jobaid 4317323 kac 2860 pg
- Technical Education Job Aid 4317323 KAC-28 Electric Built-in Single Oven60 pg
- Whirlpool & KitchenAid Built-In Electric Cooktops42 pg
Installation Guide
- Installation Instructions6 pg
- Installation Instructions7 pg
- Installation Instructions20 pg
MyPros+ Max
Diagnose your Amana RCC-3-L1.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (67)
CodeMeaning
dOOrDoor switch circuit is open, either due to keyboard entry made while main door…dSFLFault detected in the microprocessor temperature sensor circuit; buzzer will…F0Default F codeF0 E0No fault found.F1Electronic control malfunction (all E codes).F1 E2Lost communication with power board.F1 E3Configuration jumper change; freestand, electric switches or P3 pins 1 to 5…F1 E4Oven sensor not calibrated.F1 E5Meat probe not calibrated.F1 E6Display board EPROM access failure.F1 E7Power board EPROM access failure.F1 E8Improper keypad feedback from power board supply lift.F1 E9Unstable keyboard gain.F1 EAExceeded stack warning level.F1-E0Key held down too long, or key is shorted.F1-E1Keypad keytail not connected.F1-E2Damaged or corrupted memory on control board; incompatible software components…F1-E5Cancel key drive line open.F10-E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.F2Electronic control malfunction.F2 E0User is cleaning too long or keypad is disconnected.F2 E1Cancel key invalid.F2 E3Key held down too long or keyboard short or spill on switch surface.F2 E5Cancel key drive line open.F2-E1Control detected stuck key(s) in keypad or keypad connection.F2-E2User interface cannot communicate with main control; loose user interface…F3 E0Oven sensor open circuit.F3 E1Temperature sensor shorted.F3 E2Oven temperature too high (over 301°C / 575°F in Cook mode).View all 67 error codes
F3 E3Shorted oven sensor.F3 E4Oven temperature too high (runaway condition).F3-E0Temperature sensor opened.F3-E1Temperature sensor shorted.F3-E2Oven temp too high (over 301°C [575°F] in Cook mode).F3-E3Oven temp too high (over 510°C [950°F] in Clean mode).F4 E0Meat probe shorted (less than 1500 ohms).F4 E1Meat probe malfunctionF4-E1Meat probe malfunctionF4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F5 E0Door is open but latch is locked (door switch closed indicating open door, and…F5 E1Self clean latch not locking.F5 E5Self clean temperature not achieved after 30 minutes.F5 E7Door unlocked but will not unlatch during clean cycle.F5-E0Door is open, but latch is locked (door switch closed indicating open door, and…F5-E1Self clean latch will not lock.F5-E2Door stuck closed; control programmed to not start if it suspects the door…F5-E5Self clean temperature (288°C [550°F]) not reached within 45 minutes.F5-E7Self clean latch will not unlock.F6 E0Return line not connected; electronic control will display F6 within 60 seconds…F6-E0Return line not connected.F6-E1Low/no water to dishwasher (mechanical problem).F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds/air in pump; too many suds, captured wash water, or water leaking from…F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Flowmeter disconnected or damaged.F6-E8Water softener regeneration valve electrical problem; loose connection in regen…F7 E0Invalid latch switch reading.F7 E1Invalid door switch reading.F7-E1No heat; control programmed to disable heater if it detects a water heating…F7-E2Heater stuck on; heater drive circuit on the control.F8-E1Slow drain; obstructed drain hose or path.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain stuck on; drain motor drive circuit on the control.HotPossible overheating condition detected; the microprocessor controller has…PFPower failure occurred (not a failure mode).SEFLRotational sensor circuit failure indicating a fault in the basket (tumbler)…
Service modes (12)
- Customer Cycle Rapid Advance["Start a customer cycle.","Press HIGH TEMP
- End of Service Test Sequence (Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
- End of Service Test Sequence (Non-Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
- Error Code Display and Clear["Enter Service Diagnostics Cycle (1-2-3-1-2-3-1-2-3).","Interval 24
- Fahrenheit to Celsius conversionPress the BROIL pad for 5 seconds
- Fault code history recallPress and hold the '0' touchpad for 5 seconds to access the previous fault codes
- Hot condition manual resetAfter temperature drops to 220°F or lower, manually close and then open the program switch (PS) on…
- Phase 5 Coin System DiagnosticsThe Phase 5 coin microprocessor controller automatically monitors all major circuits including…
- Programming Cavity SizeWithin 60 seconds of power up, press
- Programming the cavity sizeWithin 60 seconds of power up, press the following touchpads in order
- Sabbath Mode exitIf 'SAB' appears in the display, press and hold the '6' touchpad for 5 seconds to end Sabbath Mode.
- Service Diagnostics Cycle["Press START/RESUME to wake up the control panel.","Press any 3 keys in the sequence…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana range models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass