mypros+
Model reference

Amana RCR-700-P85727-3S

Range

1 document73 error codes26 service modes

Available documentation

Installation Guide

  • Installation Instructions10 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RCR-700-P85727-3S.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (73)

CodeMeaning
d13Coin 2 sensor is detected as blocked; coin vault may be full, or sensor may be…d16Gen. 2 debit card reader errord5Coin 1 sensor is detected as blocked; coin vault may be full, or sensor may be…d9Low voltageF0 E5Off balance condition detected during operation.F01Main control fault.F03Main control detects an out of range pressure signal from the pressure sensor.F07Main control cannot determine position of shifter (shifter system failure).F0E5Off balance load detected during cycle operation.F0E7Control board recognized line voltage below 90 VAC.F1 E1Main control faultF1 E6Low voltage detectedF11Motor control faultF1E1A fault has occurred in the main control.F2 E1Washer keypad stuck errorF20Long fillF21Long drainF22Lid lock faultF24Inlet water temperature faultF25Basket speed sensor faultF26Lid switch faultF27Overflow conditionF29Lid unlock faultF3 E2Pressure sensor faultF3 E3Inlet water temperature faultF32No fillF3E1Main control detects an out of range pressure signal from the pressure sensor.F3E2Inlet water temperature thermistor is detected to be open or shorted.F5 E1Lid switch faultF5 E3Lid switch fault
View all 73 error codes
F5 E4Lid unlock faultF5E1Lid is in locked state but lid switch is open; main control cannot detect the…F5E3Lid lock has not moved into locked position or motor cannot be powered…F5E4Lid lock has not moved into unlocked position or motor cannot be powered; main…F6 E1Communication failure between CCU and UIF6E1Communication failure between CCU and UI; electrical connection between CCU and…F7 E1Basket speed sensor faultF7 E2Motor control faultF7 E5Shifter faultF70Communication failure between CCU and UIF71Communication failure between CCU and UIF73User Interface EEPROM not programmed or corrupted; UI identification does not…F74User Interface EEPROM not programmed or corrupted; UI identification does not…F77Off balance load detected.F7E1Main control cannot determine speed of basket, or speed changes too quickly…F7E5Main control cannot determine position of shifter.F7EDFault of the motor control section of the main control.F8 E1No fillF8 E3Overflow conditionF8E1No fill detected; water level does not change for a period of time or water is…F8E3Overflow condition; main control senses a water level that exceeds the washer's…F9 E1Long drainF9E1Long drain; water level does not change after the drain pump is on for 10…FC E1Model/serial not programmedFC E2Model/serial do not matchFC E4USB faultFC E5Software update failureFC E6Model setup export failureFC E7Model setup import failureFCE1No model/serial number information is saved on the machine's controls.FCE2Model/serial number information saved on the machine's controls is not the same…FCE3Wi-Fi connection fault.FCE4USB stick failure (USB full, not detected, or not accessible).FCE5Software uploaded from USB stick does not match to model number of machine.FCE6Download of machine setup from machine to USB stick failed.FCE7Upload of machine setup from USB stick to machine failed; machine number from…FCE8Wi-Fi module not responding or not connected.FP E1Coin 1 circuit errorFP E2Coin 2 circuit errorFP E3Card reader communication failure.FPE1Coin 1 circuit error.FPE2Coin 2 circuit error.FPE3Card reader communication error.

Service modes (26)

  • Calibration Cycle (P-05)["Enter Service Diagnostic Test Modes.","Press MIXED keypad until 'P-05' is displayed.","Press…
  • Clear Errors (P-01)["Enter Service Diagnostic Test Modes.","Display shows 'P-01'.","Press START to clear active error…
  • Help Mode["Enter Service Mode.","Use the NORMAL keypad to advance to program location 2.xx (Special Pricing…
  • Manual Overview Test (P-04)["Enter Service Diagnostic Test Modes.","Press MIXED keypad until 'P-04' is displayed.","Press…
  • P-01 Clear Errors["Enter Service Diagnostic Test Modes.","Display shows P-01.","Press START to clear active error…
  • P-02 Cycle Credit["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-02.","Press START to provide…
  • P-03 Quick Overview Test["Enter Service Diagnostic Test Mode.","Press MIXED until P-03 is displayed.","Press START to…
  • P-03 Service Diagnostic["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-03.","Press START to initiate…
  • P-04 Manual Diagnostic["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-04.","Press START to initiate…
  • P-04 Manual Overview Test["Enter Service Diagnostic Test Mode.","Press MIXED until P-04 is displayed.","Press START
  • P-05 Calibration Cycle["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-05.","Press START to initiate…
  • P-06 Drain & Spin Cycle["Enter Service Diagnostic Test Mode.","Press MIXED until P-06 is displayed.","Press START to…
  • P-07 UI Diagnostics["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-07.","Press START to start UI…
  • P-09 Tachometer Verification["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-09.","Press START to start…
  • P-12 Clean Washer Cycle["Enter Service Diagnostic Test Modes.","Press NORMAL to advance to P-12.","Press START to start…
  • Quick Overview Test (P-03)["Enter Service Diagnostic Test Modes.","Press MIXED keypad until 'P-03' is displayed.","Press…
  • Service Diagnostic Test Mode["For coin (PD) models
  • Service Diagnostic Test Modes["1. For coin models (PD), remove the service cover on the metercase. For card reader ready models…
  • Service Diagnostic Test Modes (entry)["For coin (PD) models
  • Service Diagnostic Test Modes (main entry)["For coin (PD) models
  • Tachometer Verification (P-09)["Enter Service Diagnostic Test Modes.","Press MIXED keypad until 'P-09' is displayed.","Press…
  • Technician Service Access Code (free vend models only)["This method is only available on washers set to free vend (6 00).","Press the LEFT UPPER, RIGHT…
  • Technician Service Access Code (PR Free Vend models only)["Press POWERWASH, EXTRA RINSE, TEMPERATURE, and DELICATES keypads within 10 seconds."]
  • Technician Service Access Code (PR free vend models)["Press the POWERWASH, EXTRA RINSE, TEMPERATURE, and DELICATES keypads within 10 seconds."]
  • Technician Service Access Code (PR models, free vend only)["Press the POWERWASH, EXTRA RINSE, TEMPERATURE, and DELICATES key pads within 10 seconds."]
  • UI Diagnostics (P-07)["Enter Service Diagnostic Test Modes.","Press MIXED keypad until 'P-07' is displayed.","Press…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass