mypros+
Model reference

Amana TM18D-P74660-1W

Refrigerator

7 documents71 error codes12 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10268745 - Rev A10 pg
    Covers this model
  • Tech Sheet - W10918869 - Rev E6 pg
    Covers this model
  • Tech Sheet - W10918869 Rev E6 pg
    Covers this model
  • Tech Sheet W10918869D6 pg
    Covers this model

Service Manual

  • SERVICE MANUAL JennAir® Columns Built-In38 pg
    Covers this model

Installation Guide

  • Instrucciones de instalacion22 pg
    Covers this model

Quick Reference

  • Quick Reference Manual1 pg
    Covers this model
MyPros+ Max

Diagnose your Amana TM18D-P74660-1W.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (71)

CodeMeaning
:Flashing colon indicates a power failure has occurred.1-1Control detected pilot relay K400 stuck closed.1-2Control software issue10-1Dispenser electrical problem10-2Vent wax motor electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.2-2User Interface cannot communicate with main control3-1Open connector or component in temperature sensing circuit (open or faulty…3-2Shorted connection or component in temperature sensing circuit, or incoming…3-3OWI (optical soil sensor) failed calibration.3-4OWI failed calibration4-3Wash motor not running due to loose connection in motor circuit and/or faulty…4-4Wash motor failure5-1Door stuck open5-2Door stuck closed6-1Low or no water to dishwasher (mechanical problem).6-2Fill valve electrical problem6-3Suds or air detected in pump.6-4Float switch stuck in overfill (open) position and/or dishwasher not level.6-6Incoming water temperature under 65°F (29°C)6-7Flowmeter disconnected or damaged.6-8Water softener regeneration valve electrical problem (loose connection in regen…7-1No heat7-2Heater stuck on8-1Slow drain8-2Drain motor electrical problem; loose connection in drain motor circuit and/or…8-3Loose connection in Door Switch Circuit and/or door switch contacts stuck open…8-4Drain motor electrical problem9-1Diverter can't find position
View all 71 error codes
9-2Diverter stuck on9-3Diverter disk in sump is missing.9-4Lower spray arm errorF1E0Oven user interface failure.F1E1Internal oven ACU (Appliance Control Unit) error.F1E4Microwave ACU PCBA failure.F1E5Microwave oven inverter error.F1E6Microwave generation error.F2Touch panel failure.F2E0Keypad disconnected.F2E1Stuck key failure on the touch panel.F3E0Refrigerator/Main compartment (Z1) thermistor short or open circuit.F3E1Freezer/Main compartment (Z1) thermistor short or open circuit.F3E2Refrigerator Evaporator thermistor short or open circuit.F3E3Freezer Evaporator thermistor short or open circuit.F3E4Deli compartment (Z2) thermistor short or open circuit.F3E5Crisper (Z3) thermistor short or open circuit.F3HHumidity sensor failure.F4E1Microwave cavity temperature sensor error.F4E2Magnetron temperature sensor error.F4E4Humidity sensor error.F4E8Inverter over temperature.F4E9ACCUPOP error.F5E0Door and latch switch do not agree.F5E1Latch not operating.F6MW relay (Relay 4903) failureF6E0Oven user interfaceF6E1Over temperature.F6E4User interface/Appliance manager state status mismatch.F6E6Oven appliance managerF6E8Lost communications with microwave oven appliance manager.F8E0Product not wired correctly (cooling fan).F8E1Low fan speed overspeed.F8E2High fan speed underspeed.F8E3High fan speed overspeed.F8E5Exhaust air temperature detection failure.F9E0Product not wired correctly (house wiring).FDE0Ice maker tray thermistor short or open circuit.FDEAIce Maker Jammed (cannot find Homing or end of harvest location).OPOpen circuit detected on thermistor.SHShort circuit detected on thermistor.

Service modes (12)

  • Clear Customer Error History["Enter Service Diagnostics Cycle.","During the appropriate diagnostics interval (interval with Hi…
  • Customer Cycle Rapid Advance["Start a customer cycle.","Press HIGH TEMP
  • DiagnosticsPress LOWER OVEN > LOWER LIGHT > OVEN CANCEL, repeat this sequence 2 more times (3 times total)
  • Diagnostics / Test Mode["Plug in microwave oven or reconnect power.","Press CANCEL button to enter Standby mode (display…
  • Rapid Advance (Customer Cycle)After starting a customer cycle, press HIGH TEMP
  • Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Rapid Advance Mode (Cycle Operation)["With door open or closed after starting a cycle, press HIGH TEMP
  • Sales Demo Mode ClearRun Service Diagnostics Cycle to clear Demo mode.
  • Self-Diagnostic / Test Mode["Press and hold the CANCEL/OFF button while opening the door.","While still holding the CANCEL/OFF…
  • Service Diagnostics Cycle1
  • Service Diagnostics Mode["Press the pulsing JennAir logo to wake up the UI.","Press the middle zone key.","Press CONNECT…
  • Showroom Mode["Press and hold top and bottom zone icons simultaneously for 3 seconds."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana refrigerator models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass