Model reference

Amana TAA800/P77040-5W

Washer

5 documents37 error codes8 service modes

Available documentation

Tech Sheet

Tech Sheet - 127281152 pg
Covers this model
Tech Sheet - 127281224 pg
Covers this model

Tech Tip

Installation Instructions2 pg
Covers this model

Installation Guide

Installation Instructions20 pg
Covers this model
Installation Instructions4 pg
Covers this model

MyPros+ Max

Diagnose your Amana TAA800/P77040-5W.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Amana Washer

F0 on my Amana TAA800/P77040-5W

M+

Default F code - no failure. Will only

From Tech Sheet W11627996, p.48:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (37)

CodeMeaning

F0Default F code F0-E0Default F code F01Temperature sensor opened (open circuit in oven temperature sensor).F02Welded element relays (element relay contacts fused closed).F03EEPROM error in electronic control.F04Communication error between master and slave electronic controls.F05Door or latch problems (mechanical or electrical fault in door latch assembly).F06Electronic control malfunction.F1Electronic control malfunction.F1-E0Key held down too long, or key is shorted.F1-E1Keypad keytail not connected.F1-E2Electronic control malfunction (E2 variant).F1-E3Electronic control malfunction (E3 variant).F1-E4Electronic control malfunction (E4 variant).F1-E5CANCEL key drive line open.F2All E codes indicate electronic control malfunction.F2-E0Temperature sensor opened (R=2875 ohm by spec).F2-E1Temperature sensor shorted (R=825 ohm by spec).F2-E3Key held down too long, or key is shorted.F3-E0Temperature sensor (lower) opened.F3-E1Temperature sensor (lower) shorted.F3-E2Oven temp too high F3-E3Oven temp too high F4-E0Meat probe shorted.F4-E1Meat probe malfunction F5-E0Door is open but latch is locked (door switch open indicating open door, latch…F5-E1Self-clean latch will not lock/unlock.F5-E5Self clean temperature (550°F / 288°C) not reached within 45 minutes.F5-E7Self clean latch will not unlock.F6-E0Lower cavity over temperature during cooking.

View all 37 error codes

F6-E1Microwave cavity over temperature during cooking.F8-E0Self-clean latch will not lock.F8-E1Self-clean latch will not unlock.F8-E2Oven over temperature while door open and latch lock.F8-E3Oven over temperature while door open and latch unlock.F8-E4Oven over temperature while door closed and latch unlock.SABOven is in Sabbath Mode.

Service modes (8)

Bake temperature offset adjustment1
Cavity Size ProgrammingWithin 60 seconds of power up, press the following touchpads in order
Default F code display (no fault check)Press and hold '0' key for 5 seconds
Default fault code display (F0-E0)Press and hold '0' key for 5 seconds (only displays if no pre-existing faults).
Fahrenheit to Celsius conversionPress the BROIL pad for 5 seconds
Fault Code Display (No Fault)Press and hold '0' key for 5 seconds
Fault Code History RecallPress and hold the '0' key to access previous fault codes
Sabbath Mode exitIf 'SAB' appears in digital display, press and hold the '6' key for 5 seconds to end Sabbath Mode.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass