mypros+
Model reference

Cont Girbau H2255

Washer

6 documents46 error codes9 service modes

Available documentation

Service Manual

  • H20 Series Inverter Alarms Troubleshooting18 pg
    Covers this model
  • Operation Instructions Handbook for Washers Control Version PM135 pg
    Covers this model

Bulletin

  • Engineering bulletin no.3191 pg
    Covers this model
  • Engineering Bulletin 3201 pg
    Covers this model

Installation Guide

  • Installation and Operation Instructions Handbook for Washers78 pg
    Covers this model
  • Installation Instructions Handbook for Washers70 pg
    Covers this model
MyPros+ Max

Diagnose your Cont Girbau H2255.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (46)

CodeMeaning
A-00Communication failure between microprocessor and inverter, inverter displays…A-01Over Current during accelerationA-02Over Current during decelerationA-03Over Current at constant speedA-04Failure of inverter relay K-2A-06Over voltage during acceleration in the DC link circuit, inverter displays OU1.A-07Over voltage during deceleration in the DC link circuit, inverter displays OU2.A-08Over voltage at constant speed in the DC link circuit, inverter displays OU3.A-11Inverter OverheatingA-12Motor OverheatingA-13Inverter OverheatingA-16Braking Resistor overheatingA-17Motor OverloadA-19Motor OverloadA-1FFailure in inverter information or parameter error, inverter displays Er1.A-21Failure in inverter information or parameter error, inverter displays Er3.A-26Communication failure between microprocessor and inverter, inverter displays…A-40Parameter error in inverter.A-55Parameter error in inverter.A-bInput Phase LossALM/A-1Emergency stop activated.ALM/A-10Faulty cold water supply or faulty synthetics cooling.ALM/A-11Blocked duct or drain valve, or failure on water exhaust system.ALM/A-12Motor overheating.ALM/A-13Failure on door lock.ALM/A-2Faulty out-of-balance detection system (H machines).ALM/A-3Faulty temperature probe.ALM/A-4Water level detected with machine OFF; bath level sensor out of adjustment.ALM/A-5Door open or faulty door lock.ALM/A-6Faulty water supply or faulty water inlet.
View all 46 error codes
ALM/A-7Persistent over-level of water.ALM/A-8Faulty heating system.ALM/A-9Too high water temperature.ALM/COMPossible failure of inverter.COMCommunication failure between microprocessor and inverter, inverter displays…ENd/BALFinal extract cancellation due to persistent out-of-balance (H machines).ENd/REdEnd of cycle with extract speed reduced due to out-of-balance in load.Err/1Washer model configuration error, Error in EPROM, or Plug X10 disconnection.Err/2Error in EPROM or RAM memory incorrect operation.Err/3Operating program blocked.Err/4Incorrect extract time programming.Err/5Error in dosings activation.Err/6Error in heating system activation.Err/7Error in rotation activation.Err/8Error in drain activation.Err/9Error in extract activation.

Service modes (9)

  • CONF mode (parameter download)["Turn off power to unit.","Modify the setup switch on board to the left position.","Turn power…
  • General Erase / Return to Basic Configuration["Access CONF 1 configuration step","Press the 0 key","Press ENTER/START key","Confirm by pressing…
  • Inverter Configuration Verification (tESt)["Access CONF 1 configuration step","Close machine door","Access STAGE 9
  • Inverter Parameters Loading (LOAd)["Access CONF 1 configuration step","Close machine door","Access STAGE 9
  • Machine Configuration (CONF 1)["Ensure display shows idle state","Disconnect the External Automatic Switch","Remove top cover…
  • Manual Mode["ON switch to I position","Programming selector to RUN position","Press MAN key","Wait for door…
  • Model and EPROM Version Display["Ensure microprocessor is not in MANUAL MODE","Turn the key to Pro position","Press 0 key three…
  • Operation Configuration (CONF 2)["Ensure display shows idle state","Insert the key inside the programming selector (fig
  • Programming Mode (PROG)["Insert the key in the programming access selector","Turn to PROG position","Display will show…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Cont Girbau washer models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax