Model reference

GE GDP615HFM4DS

Dishwasher

2 documents74 error codes5 service modes

Available documentation

Service Manual

Technical Service Guide80 pg
Covers this model
Technical Service Guide79 pg
Covers this model

MyPros+ Max

Diagnose your GE GDP615HFM4DS.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·GE Dishwasher

AcF on my GE GDP615HFM4DS

M+

High supply voltage - supply voltage is

From Service Manual 372851, p.23:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WR55X10942

Main control board

Error codes (74)

CodeMeaning

AcFHigh supply voltage AdcInternal board failure (critical fault).CFEContinuous fill error (critical fault).dLFDoor latch failure (critical fault).F1Communication error with User Interface (UI) board.F112Key stuck.F128Low rinse aid detected.F153Door latch failure.F155Key stuck.F16High water temperature.F201Flood switch fault detected.F202A connection issue has been detected at the water valve.F203A fault has been detected on the machine control board.F204A fault has been detected on the machine control board.F205A fault has been detected with the detergent cup.F206The pump motor fuse is open.F207A fault has been detected on the machine control board.F208A fault has been detected on the machine control board.F209A fault has been detected on the machine control board.F210A fault has been detected on the machine control board.F211Check heater TCO; a fault has been detected on the machine control board.F212A fault has been detected on the machine control board.F213Check heater TCO; a fault has been detected on the machine control board.F214AC connections fault detected.F215AC connections fault detected.F216Check heater TCO and AC connections; no failure detected with machine control…F217A fault has been detected on the machine control board.F218A fault has been detected on the machine control board.F219A fault has been detected on the machine control board.F220A fault has been detected on the machine control board.

View all 74 error codes

F221A fault has been detected on the machine control board.F222A fault has been detected on the machine control board.F223A fault has been detected on the machine control board.F224No failure detected with machine control board; pump motor fuse blown, or…F225Check heater TCO; a fault has been detected on the machine control board.F226Check heater TCO; a fault has been detected on the machine control board.F227Check heater TCO; a fault has been detected on the machine control board.F228Check heater TCO; a fault has been detected on the machine control board.F229Check heater TCO; a fault has been detected on the machine control board.F230A fault has been detected on the machine control board; check heater TCO and…F231CSM trip detected.F32Water level sensor invalid.F33Low pressure sensor reading.F34Leak detected.F36CSM tripped (CSM lock out).F37Diverter feedback error.F48Turbidity sensor high.F49Turbidity sensor low.F50Temperature sensor high.F51Temperature sensor low.F52Turbidity sensor calibration fail.F53Circulating pump failure.F54Drain pump failure.F55Blown pump fuse on main control board.F56Failure to drain.F58Dry heater thermistor error F59Dry heater thermistor error F60Heater relay stuck on fault.F61CSM check failed.F62Dry heater fan error.F63Flood condition fault F64Ignore fault.F66Dry heater fault.F86No fill failure.F87Dry heater diagnostic fault.F96Ignore fault.F97Absent heat source.F98Non-draining sump (turbidity based).F99Minimum wash temperature not met.FtdFailure to drain (critical fault).FuSBoard circulation pump fuse failure (critical fault).H20Water supply failure (critical fault).HrfInternal board failure (critical fault).PrSPressure sensor failure (critical fault).

Service modes (5)

Consumer Error ModeWith the dishwasher in Standby Mode (not running a cycle), press and hold the Cycle Select and…
Demo Mode ExitTo exit demo mode, hold START and HEATED DRY at the same time for 5 seconds.
Error ModeWith the dishwasher in Standby Mode (not running a cycle), press and hold the furthest most pad on…
Self-Diagnostic Mode1
Service Mode1

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass