mypros+
Error code reference

GE Dishwasher Error Code F224

No failure detected with machine control board

GE codesGE dishwasher codes

No failure detected with machine control board. Pump motor fuse blown, heater TCO tripped, or drain/circulation motor fault.

First step from the service manual

Replace pump motor fuse. Replace circulation and drain pumps. Check Heater TCO (tripped).

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F224.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F224 means on a GE dishwasher

GE dishwasher error code F224 indicates that the machine control board itself has not detected an internal failure, but the control has identified a fault condition within the pump motor circuit, heater thermal cutout (TCO), or the drain and circulation motor assemblies. Because the control board is ruled out as the source of the fault, diagnosis centers entirely on the components downstream of the board: the pump motor fuse, the TCO on the heating element, and the physical condition of both the circulation pump and drain pump motors.

The pump motor fuse is a protective fuse in the motor circuit that will blow if the motor draws excessive current, which can happen due to a locked rotor, a short in the motor windings, or debris jamming the pump impeller. A blown fuse cuts power to the motor and triggers this code. The heater TCO is a thermal safety device that interrupts the heating circuit if the water temperature exceeds a safe threshold. Once tripped, the TCO does not automatically reset and must be inspected and replaced if it has opened.

Faults in the circulation or drain pump motors themselves can also generate F224. Motor winding failures, bearing seizure, or damaged impellers all present as motor faults that the control detects through abnormal current draw or failed operation signals. Diagnosing this code correctly requires checking the fuse continuity, testing the TCO for continuity, and inspecting both pump motors for mechanical and electrical faults before replacing any component.

Source: manufacturer service documentation.

Common causes of F224

  1. 01

    Blown pump motor fuse

    Part replacement

    A fuse in the pump motor circuit can blow if the motor experiences an overcurrent event, such as from a jammed impeller or a short in the motor windings. Check the fuse for continuity with a multimeter and replace it if it has opened.

  2. 02

    Tripped heater TCO

    Part replacement

    The thermal cutout on the heating element trips and opens the circuit when water temperatures exceed safe limits, and unlike a thermostat, it does not self-reset. Test the TCO for continuity to confirm it has opened, and replace it if it shows no continuity.

  3. 03

    Circulation pump motor failure

    Part replacement

    The circulation pump motor can fail due to winding damage, seized bearings, or a damaged impeller, all of which cause abnormal current draw or a complete lack of motor operation. Inspect the motor for physical damage and test winding resistance to confirm the fault.

  4. 04

    Drain pump motor fault

    Part replacement

    The drain pump motor is subject to similar failure modes as the circulation pump, including debris blockage and motor winding failure. If the drain pump does not respond during the drain cycle or draws abnormal current, it should be replaced.

  5. 05

    Debris jamming the pump impeller

    Wiring / connection

    Foreign objects such as broken glass, food debris, or small utensils can become lodged in a pump impeller, causing the motor to stall and draw excessive current that blows the fuse. Inspect both pump impellers for obstructions before replacing any electrical components.

See the test procedure for each cause

Frequently asked questions about F224

What does F224 mean on a GE dishwasher?
F224 on a GE dishwasher means the control board has detected a fault in the pump motor circuit, the heater thermal cutout (TCO), or the drain and circulation pump motors, while confirming the control board itself is not the source of the problem. The code points to a blown pump motor fuse, a tripped heater TCO, or a failed pump motor. Diagnosis requires testing each of these components individually to identify the specific cause.
Can I fix F224 on my GE dishwasher myself?
Some steps, such as clearing debris from the pump impeller, are within reach of a capable DIYer with basic tools. However, replacing a pump motor fuse, testing the heater TCO for continuity, or replacing a circulation or drain pump motor requires comfort with electrical testing and disassembly of the dishwasher's pump assembly. If you are not familiar with multimeter testing or appliance disassembly, a professional technician is the safer option.
Is it safe to use my GE dishwasher when F224 is showing?
No, you should not continue running the dishwasher while F224 is active. The code indicates a fault in critical safety or operational components, including a possible blown fuse or a tripped thermal cutout on the heater. Running the dishwasher without resolving the fault could cause further damage to the pump motors or heating system.
Will resetting my GE dishwasher clear the F224 code?
Resetting the dishwasher by cutting power will not clear the underlying cause of F224. Because the code is triggered by a physical fault such as a blown fuse, a tripped TCO, or a failed pump motor, the code will return as soon as the dishwasher attempts to operate again. The faulty component must be identified and repaired or replaced before the code will clear permanently.
How much does it cost to repair a GE dishwasher showing F224?
Repair costs depend on which component has failed. Replacing a pump motor fuse or a heater TCO is relatively low cost, typically in the range of $50 to $150 including parts and labor. Replacing a circulation or drain pump motor is more involved and can range from $150 to $350 or more depending on parts pricing and labor rates in your area. Getting a diagnostic visit from a technician will confirm exactly which component needs attention before committing to a repair.

Related GE dishwasher codes

All GE dishwasher codes
View all 222 GE dishwasher codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass