mypros+
Error code reference

GE Dishwasher Error Code RINSING FLASHING

Control error on Profile Performance models indicated by flashing RINSING LED and beeping sound.

GE codesGE dishwasher codes

Control error on Profile Performance models indicated by flashing RINSING LED and beeping sound.

First step from the service manual

Press the START/RESET pad to turn off the beeper; if the RINSING light continues to flash, call for service.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for RINSING FLASHING.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What RINSING FLASHING means on a GE dishwasher

The flashing RINSING LED on GE Profile Performance dishwashers signals a control error, meaning the main control board has detected a fault condition it cannot resolve through normal cycle operation. This is not a standard mid-cycle pause or a minor sensor fluctuation. The control board monitors multiple subsystems throughout the wash and rinse sequences, and when it detects an inconsistency or failure it cannot reconcile, it halts operation and alerts the user through the flashing RINSING indicator combined with an audible beeping sound.

This error is specific to GE Profile Performance series dishwashers and is tied directly to the control electronics rather than a single mechanical component like a pump or float switch. The flashing pattern is the control board's way of communicating that intervention is required. Because the fault originates at the control level, the range of potential root causes spans from transient power issues that confused the board to actual hardware failures in the control assembly itself.

The prescribed first step is to press the START/RESET pad to silence the beeper and attempt a soft reset of the control. If the RINSING light stops flashing after this reset, the fault may have been a temporary glitch caused by a power fluctuation or communication hiccup within the board. However, if the RINSING LED continues to flash after pressing START/RESET, the fault is persistent and professional service is required, as further diagnosis involves inspecting or replacing control board components.

Source: manufacturer service documentation.

Common causes of RINSING FLASHING

  1. 01

    Transient power fluctuation

    Wiring / connection

    A brief voltage spike, dip, or power interruption can cause the control board to enter a fault state. Pressing START/RESET often clears this type of error with no further issues.

  2. 02

    Control board failure

    Part replacement

    If the RINSING light continues to flash after a reset attempt, the main control board itself may have failed or developed a fault in its internal logic circuitry. Replacement of the control board is typically required in this scenario.

  3. 03

    Corrupted control board memory or software error

    Part replacement

    The control board's onboard programming can become corrupted due to power events or component aging, causing it to repeatedly flag a fault during the rinse sequence. This may persist through resets and require board-level service.

  4. 04

    Loose or faulty wiring harness connection to the control board

    Wiring / connection

    A poor connection between the wiring harness and the control board can cause intermittent communication errors that the board interprets as a control fault. Inspecting and reseating harness connectors at the control board can sometimes resolve this.

  5. 05

    Door latch or door switch issue

    Wiring / connection

    If the control board receives an unexpected signal from the door switch during the rinse phase, it may register a control fault. Checking that the door is fully latched and that the door switch operates correctly is worth confirming before calling for service.

See the test procedure for each cause

Frequently asked questions about RINSING FLASHING

What does RINSING FLASHING mean on a GE dishwasher?
On GE Profile Performance dishwashers, a flashing RINSING LED combined with a beeping sound indicates a control board error. The dishwasher has detected a fault it cannot resolve on its own and has halted operation to alert you. This is an electronics-level fault rather than a simple clog or mechanical blockage. Pressing START/RESET is the first recommended step to attempt clearing the error.
Will pressing START/RESET fix the flashing RINSING error?
Pressing the START/RESET pad will silence the beeping and may clear the error if it was caused by a temporary power fluctuation or minor control glitch. If the RINSING light stops flashing after the reset, the dishwasher should return to normal operation. If the light continues to flash, the fault is persistent and a service technician will need to diagnose the control board or related components.
Is it safe to keep using my GE dishwasher when the RINSING light is flashing?
No, you should not attempt to continue running the dishwasher while the RINSING LED is actively flashing and the control error is present. The dishwasher has stopped its cycle intentionally due to a detected fault. Running it in this condition could result in incomplete wash or rinse cycles, and if a control board issue is involved, further use before repair could potentially worsen the damage.
How much does it cost to repair a GE dishwasher with a flashing RINSING error?
Repair costs depend on the root cause. If the issue is resolved by a simple reset, there is no parts cost. If the main control board requires replacement, parts alone typically range from $100 to $300 or more depending on the specific model, with labor adding to the total. Wiring harness repairs or door switch replacements are generally less expensive than full control board replacement.
Can unplugging the dishwasher reset the flashing RINSING error?
Unplugging the dishwasher for a few minutes and restoring power can sometimes function similarly to pressing START/RESET by allowing the control board to reboot. However, the recommended first step is to press the START/RESET pad on the control panel. If the RINSING light continues to flash after both a hard power reset and a START/RESET press, the fault is not clearing on its own and a service call is necessary.

Related GE dishwasher codes

All GE dishwasher codes
View all 222 GE dishwasher codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass